I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hi,
I have copied BLE Thermostat code from ARM mbed : developer.mbed.org/.../
As this code is on mbed 2 platform, i am trying to run it on embed 5.0. Getting below error...
Hello:
I dont seem to understand what the problem is. I have 2 external ICs, one is an IMU and the other is a CDC. Both have interrupt pins connected to the nordic nRF52832...
Hi All,
I am working on a project where i need to use a SPI 128x32 OLED display and a SD card interfaced over SPI to nRF52840 along with BLE. Although, i tried this with...
Hello,
I am developing a BLE app in which I need to print some logs to UART and recive some data from UART to my app.
Which modules should I use?
When I use logger...
my question is how to change the uuid in central to connect to peripheral and i want to send 20 bytes to central device using this uart_peripheral.
first of all my connection...
Hey,
I want to read the value of characteristic of conneceted peripheral. I'm using two BLE modules, one is peripheral and one is central. I connected with central to peripheral...
Hi. I have several questions about mbr.
1). Will mbr finish to write after unexpected power off?
2). Can I copy softdevice + application or only application using sd_mbr_command_copy_sd...
Hello,
We are trying to put togheter a custom mesh communication protocol based on nrf24L01+. Everything was good until we made transmission tests outside, from ground...
Nordic board nRF52 PCA10040, V1.1.1, 2017.1, 682048249.
The pins CTS, RxD, RTS and TxD are currently driven by the MCU. I want to use the SPIS0 in the nRF52832 with the pins...
Is there a Setting in IAR to program nrf52832 without Power cycling
nrf52832 does not start after programming from IAR IDE, using J-Link
But..
For both With J-Link...
I have been experimenting with using some peripherals on the nrf52832 without using the SDK. Primarily of interest to me right now is the low power comparator (LPCOMP).
...
i use nrf52832 .i want to connect device and send advertisment data at the same time. But peripheral mode cannot connct device and send advertisment at the same time. central...
Hi!
I am sorry if I had repeated questions in this forum. I would like to understand few things.
Test scenario
Central - nRF52840
Peripheral - nRF52840
Bluetooth...
