I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi,
I'm working on implementing a modem upload feature (using probe-rs) to be integrated into our production programming line.
Following the procedure described here ...
Hello,
I am trying to use the SAADC peripheral on my nrf5340dk without using the zephyr API; I am writing my program bare-metal. My goal is to set up the ADC in continuous...
Hi everyone,
I'm quite new to the Nrf Connect SDK and Zephyr.
I'm trying to implement a simple DFU (over UART) bootloader. The idea is that when the microcontroller powers...
Hello,
We have a water meter project that involves cellular and GPS functionalities, and we need to design the schematic. After reviewing the hardware design guidelines...
Running into a slight issue where the timebase for system (reference time + uptime aka k_uptime_ticks()) drifts relative to sensor sampling rates. Attempt to synchronize the...
Problem: Upgrading to newer SDK broke RTT processing of backspace character. Details: We had been using RTT with the v2.4.1 SDK (for our nRF52840 development) and yesterday...
Hello. I have a question about how to enable a 32 MHz crystal oscillator on a custom board? I have 32 kHz and 32 MHz quartz crystals on the board. I found the following config...
Hi. This is a problem that occurs on a customer's factory test client unit. Issue occurs roughly about once every few months.
Customer Development Environment Info:
OS...
Hi,
I am stuck during migration from ncs 2.6.2 to 2.7.0 (I want to finally reach 2.9.0):
``` [00:00:13.276,275] <err> bt_sdc_hci_driver: SoftDevice Controller ASSERT:...
Dear customer support people,
I'm trying to employ a particular signature scheme to benchmark it against other more traditional methods on your devices, specifically on...
Toolchain v2.70, SDK v2.7.0, VS Code, Windows
Kicked off an application FOTA update, and somehow it failed:
[00:02:06.161,315] <err> download_client: Error in recv(),...
I've built a firmware based on the hci_uart sample with the softdevice controller. The board is custom made and has a nrf52840 on it. Over USB-CDC HCI commands are sent to...
Is there any issue with using the nRF52833 DK/nRF52833 for Matter development? I’m asking because the Matter template doesn’t seem to support the nRF52833 DK/nRF52833. If...
Dear Nordic People Recently I am following YouTube link from Nordic Semiconductor for Implementing ESL https://www.youtube.com/watch?v=VeLkptpSvRQ This video requires specific...
Hello and thanks for reading. Also happy holidays.
We are using an NRF5340, and are having some issues with connectivity. I would therefore welcome any suggestions you may...
