hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hello,
I am trying to use several Thingy 52 as peripheral devices, (sensors) connected to a central (Gateway) particle Argon running ( nRF52840). The idea is to connect...
Hi, I have 2 questions regarding multiple controllers using nRF Mesh.
1. I used the import/export option to transfer the network details from Phone 1 to Phone 2. After import...
now I'm on going NRF24LE1 project to low power mode. I try to find several reference as link below, but both of them can't open, someone can help me ?
https://www.nordicsemi...
I have just purchased a nRF52840-DK
I am following the getting started tutorial and when I scan for devices the Nordic_prox device is not appearing in the device list but...
Is it possible to use the NRF cloud outside the dev kits? Working on a custom pcb with custom software and would like to use NRF cloud for it.
---- Christopher
Hi ,
I am working on NRF DFU firmware update. for that i am using secure bootloader code .
I tried with the of way of flasing bootloader code on my custom board and sent...
Hello Nordic community,
I updated latest modem firmware v1.1.0 in nRF9160 custom board. After flashing application code into custom hardware I power off and power on board...
Hello,
I have a question about hardware for Bluetooth LE Audio.
I see Nordic is working on a dev kit:
https://blog.nordicsemi.com/getconnected/le-audio-unveiled-as-the...
HI
I am programming NRF52840 dongle using nrf52840 dk
i have flashed blinky code to my nrf52840 dongle it programmed sucessfully after that i have erased the dongle by...
Hi there,
I'm trying to use the aws_fota example with nrf9160 and AWS and it works fine. The problem is that in my country we don't have LTE-M, so we decided to use a...
Hi,
My application returns ERROR 8 [NRF_ERROR_INVALID_STATE] after I click disconnect in the app "nRF connect for mobile" .This error is returned by "ble_advertising_start...
I try to run samples/bluetooth/scan_adv on nRF52840/nRF5340 using nRF BLE Controller..
Result is nRF52840/active scan: 498 packet/s nRF52840/passive scan: 507 packet/s ...
i have done read and write operations on fds with dummy buffer. now when im writing new data into fds it is showing the previous data .can anyone give the function to erase...
I am trying to build a solution based on the nrf_ble_uart_c example. Building has been working fine until I added pin configuration statements.
I've tried relocating the...
I am incorporating the "pin_change_int" code to generate GPIOTE interrupts from an external device. I made a couple changes including renaming the function from gpio_init...
