Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
1. I need to know the bluetooth 5 range of the nrf52840 dongles which I need to use on custom boards.
2. Can I use AT commands to communicate with the dongle over...
Hi,
We are trying to get the serial dfu example from sdk 14.2 working with an nrf52832. After flashing the device succesfully and starting up the bootloader we were unable...
Hello,
I recently switched to linux and I have many problems since then.. So I noticed that printf functions are not working fine for me e.g. in ble_peripheral_uart example...
I've worked with other integrated radio + ARM processors that were not deterministic, and I would like to know if the Nordic solution is.
What I mean is: Is there a way...
Hello all,
How does the handling of ble events work with SDK 15.1? When I register more than one event handler with the macro NRF_SDH_BLE_OBSERVER(), how does the softdevice...
Hello Support team,
I'm working on a project where I am designing a custom board uisng the Nordic NRF52840 as the MCU (forgive me if I'm using the incorrect terminology...
Hi,
I am relatively new to programming hardware at this level, and have developed our product on the 52832, so finally I have purchased the Power Profiler Kit, and downloaded...
Hello good morning,
I am using nrf52840 device. I am sending 20 bytes using notification at different notification intervals like 30ms, 80ms and 1sec. But at application...
hello
I am currently trying to use the thingy_52_sdk sample code to embed a program using the J-link debugger with the Nordic thingy 52 development kit. But the build is...
Hello,
I am attempting to test slew of Rigado BMD-350 module BLE radios (uses nRF52832) using a Rigado BMD-301 series Eval Kit to act as the central. The BMD-350 device...
Hello everyone, the sdk version that I use is 15.0 (nrF5_SDK_15.0.0). The soft device is s132. In the ble_peripheral / ble_app_uart example you can only connect through the...
If followed the following steps:
Installed Win10Pcap
Installed Wireshark-win64-2.63 on Windows 10.
Using nrfGo Studio loaded sniffer_pca10040_51296aa.hex (after erasing...
Hello fellow Nordic Community,
We have a usecase in which it would be beneficial with a tx power of - 30 dBm . This is a value that was supported with the nRF51 chip series...
Hi,
I am develop a project with dfu and bond features. I found that in dfu project, IS_SRVC_CHANGED_CHARACT_PRESENT is always set to 1. In my understanding, if set this to...
hi,
i am using Nordic thingy:52 with a nRF52840 with s140 softdevice to receive multiple characteristic data from thingy like thingy environment service have 6 characteristics...
