hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Now，I use a 1s timer to calculate the clock.
At first,I use the telephone to adjust the time to fit the telephone time.
but finally(after a night ) the result runs fastly...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
I'm trying to get a UART example running on the nRF51822 mbed kit. However, flashing any uart examples from the SDK onto the board generates a fail.txt file
What is the...
Hi, i build my own custom board with a NRF52832, i'm having problem with the softdevice (i think so)... my code is base on BLE s132 central and peripheral...
I developed...
I'm using PCA10028 board.
I copied hex file of ble_app_uart project to this board. And then I scanned via my device - Galaxy Note 5, cutting edge phone.
But I couldn't find...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am trying to achieve the maximum throughput when using the nRF51822.
According to the answer in this link ( devzone.nordicsemi.com/.../) , operation mode (write...
Hi,
I have a beacon Kit PCA20006. I have programmed it with
SOFTDEVICE
C:/Users/Arsalan/Desktop/Engineering/Devices/nRF51822/SDK/sdk11/components/softdevice...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hi,
I am working on the heart_rate_collector example code of nrf51-ble-driver_linux_0.5.0 . I try to modify the example code let it can connect the Environmental Sensing...
I have implemented static passkey onto ble_app_uart.
I would like to configure this passkey through uart, then store it in the flash. I am confused at the choices available...
Hi, I'm having some trouble connecting to the nrf51822 chip and I've tried connecting to it using master controller, nrf connect, and nrf toolbox. The chip isn't even appearing...
Hi,
I'm working on NRF52 NFC and I meet an issue related to timing.
I'm using hal_nfc_t2t driver directly (Without nfc lib) because I want to do some custom work and I...
Hello !
I am trying to read WHO_AM_I register from a LSM9DS1 IMU.
I have spi_update_imu_data() as my callback for when the spi transfer completes and inside it I make spi_xfer_done...
