Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
I have nrf52840 DK board, running cutom image that implements BLE central, constantly scanning on coded (S8) phy. Trying to add NFC T2T tag, and it doesn't work. Disabling...
Hi,
While characterising low-battery behaviour of the nPM1304 on the nPM1304 EK I see the following:
1. With VBAT above ~2.4 V, Ship mode current is ~0.40 µA, as expected...
In the bare metal SDK, for the cgms routine, if we switch to the internal LRC, how should we configure it?
CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC =y
After making this configuration...
Hi! I know that FindHub is supported on nRF Connect SDK, but I'm wondering if there is any support for it on nRF5 SDK for the nRF52840? The use case would be adding the feature...
Hi,
I'm using the Thingy:91 X PCA20065 rev 2.0.0 as a reference for a new nRF9151-LACAA1A design, and I would like to make sure I understand the recommended correction for...
I am beginning to work on a next generation of environmental sensors. The current group of sensors use the i2c, or oneWire communications bus. The current standard micro-controller...
I have two questions: 1. The MCU platform is Apollo4MP, and the battery must be customized with a capacity of 28mAh. The PM model is nPM1300. When using its battery capacity...
Hi
I'm using NRF54L15 DK from Nordic. I have installed VS Code and NRF Connect SDK and toolchain V3.4.1.
I'm following the Fundamentals course, and doing Lesson 1, exercise...
Hi,
I'm evaluating the nrf54l15dk and am trying to make a small application where nrf54 appears as a tag. Upon initialization the `nfc_t2t_setup` returns -1 which does not...
There are two USB ports. IMCU and nrf5340. I had a lot of trouble with bad cables but i found one that works and I find that I have a jlink drive that pops up so I know there...
What this ticket reports
We ship a battery-powered nRF5340 product using the nRF Connect SDK's documented production security configuration: immutable bootloader (NSIB/b0...
Hello,
I have been a Nordic DevZone member for several years, but I have never published a blog post.
I would now like to contribute a technical article about an open...
