hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Cannot connect to ATECC508A through TWI with NRF52832. Tested with nRF5_SDK_12 twi_master and deprecated twi_sw_master. It was working fine only with NRF51822 nRF5_SDK_12...
Can nRF51422 or nRF51822 can be used as bluetooth device for Raspberry pi?
As I can see on the terminal Linux, the hciconfig log says, raspberry pi 3's Bluetooth device...
Hi,
I recently migrated our code to the SDK 13 (we use the nrf52832) and now the function:
uint32_t err_code = ble_radio_notification_init(6, NRF_RADIO_NOTIFICATION_DISTANCE_5500US...
Hi,
I can't discover more than 5 characteristics on central with SD130 2.0.0.
I have trided nRF Connect and characteristics were discovered successfuly.
Is there some limit...
Hi,
I have a situation as below.
I have the list of host addresses (public type). Based on the command received, BLE peripheral device should advertise in direct advertising...
Hello there,
We are using nRF52832 custom board. I2C and GPIO are working on it. Then I uploaded BLE program (which is tested on nRF52-DK) but BLE is not showing up at...
Hey Guys,
I noticed when I use nrfutil DFU BLE command on the nRF52 DK the nrfutil program a "connectivity firmware" before the perform the DFU BLE to a Target device....
hai
i have tried to store and update some data in flash using pstorage. on storing data data is stored successfully.
#include "mbed.h"
#include "pstorage.h"
#include...
Hi all ,
hi NORDIC team ,
I'm currently developping a multiprotocol adapter LORA/BLE . I'm using the sd130 .
Semtech's third party says that it's "recommended " to have...
52832，SDK12.0.0
I met such a situation:
In the use of JLink burning program or air upgrade, after the completion of the program card died in initialization low-frequency...
If I am programming a BLE Server device, and I configure a characteristic with BLE_GATTS_VLOC_USER and queue a notification with sd_ble_gatts_hvx(), how soon can I update...
We're developing with SDK 10.0, nrf51, softdevice 8.0.0, s110.
We started with the ble_uart_app and added our own functionality, which includes the timeslot functionality...
the code is
nrfjprog -f nrf52 --snr --memwr 0x10001080 --val 0xabcd0102
I am doing the example infocenter.nordicsemi.com/index.jsp
I am able to get everything up to...
Hi,
I am currently going through the GCC and Eclipse tutorial. Now I struggle to compile the project.
I installed the blinky project (nRF5_SDK_11.0.0_blinky_blank_pca10040...
Hi all,
nRF52840 and S140 support bluetooth 5. Bluetooth 5 expands 8.x adv data length. I test it on the ble_app_att_mtu_throughout example and add more 30 bytes data to...
