Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I don't know if this is a hardware or a software problem. My nRF52832 code runs correctly on a PCA10040 development board (UUID = E9:4A:AF:04:D2:16). My custom hardware advertises...
My software sent 2422, and I saw it on the net. 2417 also has one.
And the same goes for everything else, which is basically 5M off.
What is the reason?
Hi all,
I am working on troubleshooting intermittent application resets with an nRF52840 and nRF Connect 2.6.1. Codebase is small, complexity of the project is still small...
Hello,
I'm working on a BLE central multilink application, where I want to get the list of all peripherals in range, In order to let the user select the needed periherals...
I implemented UART communication as follows, but occasionally the same data is sent twice.
Enter the critical region (app_util_critical_region_enter).
Store the transmission...
hello!
I'm using 'NRFX_LOG_INFO' for debugging purposes. However, the code seems to stop progressing when 'the NRFX_LOG_INFO' statement is removed from the section below...
Hi,
I am using an nRF52 DK board to perform some very simple tests. All I need to do is receive a line of text over serial, perform some calculations and return another...
HI
I'm trying to use lpcom to detect when the battery voltage is dropping.
The configuration is as follows: 5V battery voltage output is reduced to 3.0V through LDO...
For my application I need the UART TX/RX pins pulled low until I am ready to turn on the UART. Is there a method in Zephyr to do this? Currently when Zephyr starts it reads...
I saw some similar question, but none is what I am experiencing.
I notice some weird behavior while testing DMA mode, so I made a simple setup:
I set the DMA buffer to...
Hello everyone,
I have two devices: a Thingy53 acting as the peripheral and an nRF5340 acting as the central. I have a characteristic in a service that I want to modify...
can I send the data from the internal sensors of the stm32l4 card to nordic thnigy 91, then the latter send the data from its internal sensors and the data which is already...
I use CONFIG_UART_ASYNC_API feature of NCS v2.0 with nRF52840DK, but when UART_RX_RDY event triggered, evt->data.rx.len is smaller than the number of bytes it has received...
