void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
in Memfault I see the device ID number for each device such as 41EF6BB8FB6C9AF9. Is the distribution for the first 3 bytes the same as the distribution for the last 3 bytes...
Hello! I'm using Zepyhr OS with nrf connect SDK v3.2.3 and the NRF54L15 hardware.
I am using UARTE with the async driver (direct memory access). This is my uart configuration...
After a full consume of an spsc_pbuf , the buffer can become logically empty while rd_idx and wr_idx both remain at a non-zero offset. This breaks the next large allocation...
Dear Team,
We are currently using the nRF52833 as the BLE advertiser (cattle node) and the nRF5340 as the BLE scanner/gateway. The system is based on BLE Extended Advertising...
Hi,
I migrated my software from SDK11 TO SDK17
(Changed the BL + SD + APP)
Now i want to upgrade to (SDK17) old units (with SDK11) in the field.
Do you have any advise...
Hi There,
I am currently developing an LTE-M application on nrf9151 using ncs v3.2.1, the device is a MQTT client that publishes telemetry periodically every 3 minutes,...
I'm using nRF Connect for Desktop on Linux and updated today to v5.3.0.
I have J-Link V9.24a installed and it is available in $PATH. Also it works well with Programmer v4...
Hello, My nRF54L15-DK has suddenly stopped working, and it appears to have a hardware-level power failure.
The board was working normally the previous day while running...
We have designed a custom board around nRF54H20 EngC revision and testing it on NCS 3.1.1. We were able to do provisioning and bring up using iron-side binaries. But got two...
Hello,
I am evalating the nRF9151-SMA-DK with a Monogoto SIM card that uses Skylo NTN connectivity.
I am able to reach the internet, since DNS resolution works:
...
Hello,
We are using a custom board based on the nRF5340 + nRF7003 Fanstel module with NCS SDK v2.6.2.
Our application uses MCUboot with dual-bank OTA updates. The secondary...
Hi,
What file or files should contain CONFIG_GPIO=y for a simple application developed with nRF Connect SDK v2.9.0 such that VS Code does not show squiggles under #include...
Hi,
BLE throughput differs between NCS v2.6.0 and v2.9.2. v2.9.2 appears to have fewer MoreData packets. (Both have CONFIG_BT_CTLR_SDC_MAX_CONN_EVENT_LEN_DEFAULT set to...
Hi, Team:
I want to make an LED blink during OTA upgrade and stop blinking after upgrade.
How do I configure prj.conf, sysbuild.conf, or provide some demos
Thank you...
