here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi all,
What's happening?
System reboots when "flash_erase" is called with parameters offset 0x1f000 and size 0x1000
Setup:
NCS v2.0.0
nRF52832 with 512K flash...
Hello,
Been chasing this undefined reference to `__device_dts_ord_XXX' issue around for awhile now with no clear path forward. What I am observing is extremely similar to...
Hello,
I am working on Thread client server based network. I am using nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8. My development hardware is nRF52840-DK, HW Version 2...
Hi,
I am using nrf toolchain v2.0.0, and am testing the dfu-ota example over BLE by following the below link ( ) . howveer for fast boot up, i am using "
CONFIG_BOOT_VALIDATE_SLOT0_ONCE...
It is possible to change the partition table through a FOTA?
Is the partition table stored somewhere on the device, or is it merely used for linkage? If it is linkage only...
Does anyone know how to use the CMSIS-DSP FFT library on a nrf52832?
I am using the nrf Connect SDK and it seems all of the examples are for nrf5 SDK.
I am looking to...
i use the ubuntu20.04 and open nrfconnect-3.11.1-x86_64.appimage through proxy successfully
then i install and open the toochain manager , there is not include NCS 2.0...
We are developing a new product and plan to use nRF52810. As I understand nRF52 will be supported for production in the new nRF Connect Release (1.3.0) that will come soon...
Hello,
Our application requires the device to go into deep sleep and wake up every 24Hr or on the Accelerometer interrupt. We were able to obtain the sleep mode and wake...
I'm trying to migrate my project to NCS 2.0.0 but having an issue like below:
c:/ncs/toolchains/v2.0.0/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm-zephyr-eabi/10.3...
Hello everyone,
I am working with the SDK v17.1.0 with the DK nRF52832 with the examples of ble_app_uart and ble_app_uart_c.
I managed to implement a multilink communication...
Hi We have designed some boards with ESPRESSIF WiFi BLE Module ESP-32-WROOM-32E for control and monitor.
Is it possible to connect esp32 to nRF21540 to extend range ( such...
Hi, I am using nRF52840 and communicating with Simcom GSM( Sim7600g ). 1- Is there any example code/ Library to connect with the MQTT server?
2- Can I use this example code...
I found my thread device to have quite a large latency so I analysed the communication and found out that the device is actually timeouting and retrying before listening for...
We are trying to connect MQTT over IPv6 with nrf9160dk and custom board. We are using mqtt_simple sample.
Software NCS version: NCS main (latest)
Changes in the code:...
