void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
I just got started with the nrf9160 DK and I tested it with the Asset Tracker application (following the getting started video). At first everything was working fine and I...
If I am creating an application using the Zigbee stack running with nRF Connect SDK and Zephyr, what hardware is not available to me because it is already consumed by the...
I have both a NRF9160DK which I can program and, Zephyr, blinky Serial modem etc, all work on the DK and I also have a nrf91 Thingy.
The Thingy won't respond to programming...
Hi Nordic
One of My customer employs nRF52832-QFAA in their product. They use SDK 17.0.2 and SES to develop their product。
They found the flash is now enough(they use...
I have a NRF52840. To save some energy I wanted to disable the soft device so that there's no bluetooth activity at all. However instead of an average consumption of about...
I am developing BLE Mesh product with `nRF connect SDK`.
I understand most of sample project has a function of proxy node. But I don't know how to connect a provisioned...
I've upgraded several Thingy91 boards successfully with the latest firmware and have ran into an issue with another Thingy91 that I've purchased. Here is the error when I...
Hi,
I am storing sensor data into flash and sending it to client when it is requested by Indication characteristic.
I don't have any issue with reading/writing/updating...
Hello developer,
I am new here and learning Beacons with the Board nRF52840 Feather from Adafruit as scanner and Segger Embedded Studio. I refer to nRF52 SDK 17.0.2 and...
Hi all,
I have connected my PPK II to my pc (Ubuntu), installed the software and connected the device.
I can't seem to find the mode or start button anywhere on the user...
Hello everyone,
I am using the fanstel BC840, where the tx and rx pins of the uart are alloced on 1.02 and 1.01:
So i have created a custom_board named hello_board...
Hi,
I’m trying to test/confirm the accuracy of the 32kHz crystal oscillator and the 32MHz crystal oscillator by toggling a GPIO at a derived rate and at 50% duty. But I...
The tag options did not include just nRF Connect as an option so I picked something that had nRF Connect in it. This issue has nothing to do with the SDK.
This is a question...
Help me simple LED Blinkink nrf51822 AA type i'm using YJ-14015 and stlink compiler.. i'm also using keil for IDE. i don't know how to create program and setting for compiler...
