I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
develop tool is nrf5340dk and sample peripheral_uart in NCS1.5.0 ,when debugging , function uart_cb() alway run in case UART_RX_DISABLED and case UART_RX_BUF_RELEASED
,code...
Hello,
I am developing a product using nRF52840 and BLE communication of my product uses NUS.
SD: s140_nRF52_v7.0.1
SDK: nRF5_v16.0.0
Recently, I want to encrypt...
I am using a nRF52840 with " SEGGER Embedded Studio for ARM 5.10a" and " nRF5_SDK_17.0.0_9d13099 " sdk.
I am enabling a interrupt on a GPIOTE pin using this code.
I...
Hi,
I need to store some "XML" data in a buffer, to send over serial.
I have some trouble with storing this variable, due to some symbols.
char N_Pos0[150] = "<txid...
Hi,
I've had a product that's been out there for years. In it, we call `sd_ble_gattc_primary_services_discover` a few milliseconds after we've received `BLE_GAP_EVT_CONNECTED...
We would like to try using the standard DFU process to update third party ECU connected to the nrf52 chip. Our idea is to modify the standard DFU zip package - to add a new...
https://www.novelbits.io/bluetooth-5-advertisements/ i have followed this. want to know in simple words how periodic adv is helpful in contrast to simple advertising
The Attach LTE is working but i can't use some command AT for testing Data, as you can see in the screenshot below, i tried with somes commands but it's failing, can you please...
I think the figure 10 in nRF9160_PS_v2.0.pdf chapter 5.1.3.1 is worng.
R and C should be swapped.
It is different to Figure 118 chapter 10.3.1 R2, C10.
Exist a list...
Hello,
I have the following problem. I am using the SDK for Mesh 4.2.0 with the nRF5 SDK 16.0.0 on the nRF52840 DK, I am using the sensor model and I have extended it with...
Hi,
I want to make a BLE Multirole application where the central demands LESC, bonding and MITM and peripheral connections is JUST WORKS bonding.
Is that possible? If...
I'm trying to modify the flash_fds example to write a start time when a button is pressed, then an end time when the button is released. I get the time over TWI from an RTC...
Hi, We are into Commercial health devices using nrf5340 and looking to use AoD technology for our device to get its indoor location. We need to have a Receiver with antenna...
What are different options to load the soft device on custom board? Currently, I am using nRFGoStudio to load the softdevice on nRF52840 DK. We will not have segger hardware...
