VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
I need to configure 2 devices as relay nodes in order to relay messages from the client node to the server node
How can i implement this in the light switch example ?
I know this has been asked a few years back, but wasnt sure if there were any changes to this. I want to be able to detect when a connected device is removed from windows...
Hi,
I use nRF5_SDK_15.2.0_9412b96\examples\dfu\secure_bootloader\pca10040_ble bootloader. I upload my app to my board using PCA10031 and nRF Connect v2.6.2 on Win10 and...
Hello,
Our board is based on nRF52832 with S132 5.1.0, without RTOS. Now we have a requirement to protect sensitive memory areas with MPU, so I'm trying to run firmware...
Hi,
I am using nrf 52840 development board for developing mesh. I am using segger IDE in my windows 7 desktop for code flash to the board.
The SDK I am using is nRF5_SDK_15...
Hello to everyone.
I have a doubt about the function of NRF_LOG library in nRF52 DK. I´m trying to display the voltaje value from pin P0.26 on Termite, so I saw in this...
I have a eval board pca10040 and a custom board both having nrf52832 chip, on the eval board the nrf_sdh_enable_request function calls happens successfully with error code...
Hi Folks,
I am trying to get some data to persist past a reboot. I noticed the ram_retention_pca1004 example and it showed a simple assignment of:
NRF_POWER->GPREGRET...
Using SDK15.2 example ble_app_hrs, i need to transfer custom messages and values to the phone app so i want to use ble_nus service, i did everything as in the example ble_app_uart...
This PAN states:
"Conditions • GPIOTE is configured in event mode • TWIM/SPIM utilizes EasyDMA"
What is not completely clear are these two separate conditions? Or do both...
Hi,
I am using the 2 NRF52840 boards, rev 1. I am using SDK 15.2. The first board is running the NRFX_SPIM example. The second board is running the SPIS example. The rx_delay...
Hi,
I am trying to combine TWI and SPI peripherals to the ble_app_uart exmaple in SDK 15.2
I am facing the following error
.\_build\nrf52840_xxaa.axf: Error: L6200E...
Hi,
I'm exploring the HID keybaord example of nrf5 SDK V12.3.0, and get a problem:
I first connect my iphone to the device, and it's working, if the device is 'ignored...
I am working on a linux vm 16.04 and playing with the pc-ble-drive-js library. I recently got the board up and running and started looking at the heart_rate_collector example...
Hi,
without providing too much code right away, I would like to ask how I could circumvent AT command interface hangups. My current test application calls AT commands like...
