[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
The Bluetooth connection is disconnected, but no disconnect message is printed, and no more ads can be searched, the main thread is running fine, and the Bluetooth function...
I'm trying to just do a pristine build using the Ezurio Pinnacle 100 DVK When I originally created this project from a dev board, the resource "atmel,sam0-pinctrl.yaml" and...
Hello,
We are using the nrf52832 in SES with the softdevice s112 (v7.2.0) and sdk17.1.0 in a custom board for a BLE application (that includes OTA DFU and a custom service...
Hİ,
I can connect to LTE. but somewhere which I think it might not be the signal, it can not connect and restart (reset). not return any error. if I change my location ...
Hi there,
I have purchased a Fanstel BU840XE device ( BU840XE, The longest range, Remote USB Dongle for BLE 5, Thread, Zigbee — Fanstel ) theres the link. The device has...
Hi,
1. How can the read slave interval be reduced to less than 2ms: twi_master_with_twis_slave
2. Test environment:
DK: pca10056
SDK:nRF5_SDK_17.1.0_ddde560\examples...
Hello,
I am aware that there is going to be an update to the BLE stack and you are soon releasing 2.8.0. For NCS 2.6.0 we were using 239354 for the host subsystem and...
Hi,
I use Nordic nRF52840 BLE Sniffer Dongle and this works as expected in Wireshark up to version 4.2.7. Hówever, when I upgrade Wireshark from 4.2.7 to 4.4.0, the Dongle...
In Software Maturity Levels under Trusted Firmware-M , it is stated that only the minimal build is supported, while the full build is still considered experimental.
In Running...
We have tried the following changes, but couldn't get expecting results.
Sometimes unable to pair two devices / Sometimes fails to link with one device
Could you answer...
Hi
We are using the nRF51822 with the SoftDevice S130 V2.0.1.
The nRF51 communicates with another controller via UART with a special handshake-mechanism directly on the...
I am trying to use the external flash on my NRF5340dk to store and read data files. Raw IO from the spi_flash sample seems to be working fine, but I'm not sure how to mount...
Hi,
I use CAF LEDs with PWM. I have a timer that would make device wake up every 20 seconds with a CONFIG_CAF_POWER_MANAGER_TIMEOUT to make it sleep 2 seconds after waking...
Hello,
I’m trying to get an nRF21540 FEM working with a chip-down nRF5340 design under NCS v2.4.2. I’m able to enable the FEM at its default gain setting, but I hit a wall...
