Sorry if this is too off topic, I actually don't have any problem with my nrf52840 dongle, but the App I'm communicating with. But maybe someone of you has run into the same...
Hello!
We are planning to purchase an electronic component nrf52840 and produce a finished product on it.
question
1. Will it work immediately on the ZIGBEE 3.0...
Good morning, I have a question about NRF Util. I need to make some changes in souce code of nrfutil for my own needs, but the most recent version, which is provided on Github...
Hi. I interested now for direction finding in nrf52 series. I have nrf52811, nrf52833 and other controllers. But i don't find any information how develop board for recievers...
Zephyr Eddystone example is connectable after power on of nrf52833 board. But after disconnect it becomes non connectable. How to fix it? And how to change advertisement interval...
I am using nrf52833 to make a Thread end device as SED and RCP. All firmware versions use NCS V1.8.0.
The compilation options for OTBR is: CMAKE_OPTIONS += \ -DOT_THREAD_VERSION...
Hi,
I use the BLE_APP_UART example for reference and in the code there is the ble_evt_handler with the following states:
case BLE_GAP_EVT_CONNECTED: case BLE_GAP_EVT_DISCONNECTED...
Hi,
I faced the exact problem nda , here . I take step just like nda did before. I unchecked "Enable debug options" as Marte Myrvold told, but still the same problem.
...
Hi,
I'd like to test the Adafruit NFC reader example provided in nRF5_SDK_15.3.0_59ac345. I'm using a nRF52832DK and I2C communication, as shown in the picture:
The...
Dear Nordic Support Team,
I am developing an application for the nrf9160 DK version 1.0.x (nrf connect sdk 1.8.0 and modem firmware 1.3.1). The application depends on other...
I have a project that is reading an external flash chip via qspi. Everything is working well, and I haven't defined the sfdp-bdp field in the overlay file that defines the...
Hi All,
I am trying to test the SPI flash example provided in the zephyr samples folder. Below is my qspi dts configuration.
SDK used: NCS v1.7.1
Same code works in...
Hi Team,
We build the bare application with nRF52840 Soc with the SDK Version 16 with out any RTOS Layer. We are planning to port our code base to Zepher RTOS layer.
We...
Hello everyone!
I am trying to get my Thingy 91 to work, but I am stuck.
When I flash it with pre-compiled .hex at_client sample ( "thingy91_at_client_2021-12-15_cfedfdfa...
Hi, I'm working on nRF9160 modem firmware update.
I have used nRF9160: Full modem firmware update using SMP Server demo and compiled it for nRF9160dk board. While compilation...
We are building an application using McuBoot and Zephyr, providing the provisioning via haptools and packing the image all together. What currently bothers me is that I cannot...
Hello,
I am attempting to use SPI and I just wanted to trial the transceiver option however I am not having any luck. I have tried it three ways but as you’ll see I’ve made...
Hi
few questions on DPPI:
where is it possible to find examples in nRF Connect SDK to learn to use DPPI on nRF91?
Is there corresponding documentation?
For which...
I stopped reconfiguring the broadcast configuration and started the broadcast in the following order: ①, ②, and ③. However, I found that the system may report a hardware error...
Hi Team,
I am trying to test on BL653 Nordic board with inverted polarity but we are getting error.
In given example "nCS\v1.8.0\zephyr\drivers\pwm\pwm_nrfx.c " can see...
