Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I am using nrf52832. I am making custom board file .I am little bit confused which function are used for set the pin as output or input.
__STATIC_INLINE void nrf_gpio_cfg_output...
Hi All,
from below post, I found that in SDK11, bootloader code uses NRF_UICR->CUSTOMER[0] register for device type and revision verification so application should not use...
Hi
This is Joe. I would like to ask questions about implementing BLE bonding.
SDK: 16.0.0 (nRF5SDK160098a08e2)
Projects: The base project I start with is NUS example...
Hello,
I am trying to develop BLE custom board. It's my first time dealing with Nordic MCUs and RF. I want to understand if I am doing it all correct. Here is a piece of...
Hi,
In the I2C communication,the nRF52840 SoC is master, the sensor SCD 30 is slave. The sensor SCD 30 needs the clock stretching period, the period time is 12ms or 150ms...
Hello,
I have a general question for you.
When we develop an application from one of your examples and then you put online a new version of your SDK, do you have any advice...
Hello, I am using the nrf9160 DK and connected it with a SIM card of a local provider. The SIM card is able to connect to the LTE network and NB-IoT.
For researches I only...
Hi, I am developing a multi-link central using NRF52832 and SDK 16. I have implemented the scanning part and NRF_BLE_SCAN_SCAN_DURATION = 0. I am using address filter for...
Hi Nordic Team,
I know there are many tickets raised concerning this error 133. It is a quite generic issue with Android devices of various android versions and I have gone...
Hi, I have a problem find bluetooth device on more android phones after them unpair.
First time phones find device and connect but after unpair phone not find devices. ...
I want to make printf_test.c file into a lib file and join my nrf9160 routine, but don't know how to generate the lib file and how to join the lib file?
The measured project...
Hi everyone,
I'm using the nrf5_SDK_for_Mesh_v4.1.0 and i'm having troubles by trying to change the BLE name.
In the function gap_params_init i added a code to concatenate...
Hi,
I am currently using NRF52832 with SDK17.0.0.
As I know, a BLE central device can reach up to 20 peripheral devices.
So if I use an Android App as a central device...
