Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
Hi,
currently trying to boot up mcuboot with nrf54l15 pm_static for both cpuapp and cpuapp_ns. Both files are included in the zip file.
I have already tried several configuartions...
Hi,
I'm using nRF9160DK with SDKs v3.0.0
I am trying to use A-GPS with nRFCloud REST. I used the location example and it works correctly. The documentation states that...
Does increasing the sample time on the SAADC increase the accuracy of a single shot measurement on the SAADC? I couldn't find anything in the datasheet regarding accuracy...
Hello,
I would like to use nRF52810 chip.
And I want to implement PCB trace antenna and PCB chip antenna on same PCB(for provision)
Either PCB trace antenna or PCB chip...
I am using the SPI peripheral for communicating with a network through long wires. Is it any information about the impedance of the driver outputs from the nRF52832?
I will...
nRF52840 OPS v0.5.1 section 16.16.2 states “A pin reset is generated when the physical reset pin on the device is asserted”. This seems to contradict the descriptive name...
Dear Nordic
All our last SDKs in "example/dfu" have same error.
Code is not corect:
nrf_clock_lf_cfg_t clock_lf_cfg =
NRF_CLOCK_LFCLKSRC;
Impossible properly...
Hi Nordic Support,
According to the answer in question:
devzone.nordicsemi.com/.../
it is not possible to update the bootloader (which is the case with "bootloader_secure_ble...
I am trying to set up RTC2 by following an example
github.com/.../saadc_low_power
I ported it to my project which is running a softdevice on nRF52. It works perfectly...
Hi Alls,
I'm trying to compile and test the example project from SKD_12.3.0 and receiving the following error:
#error app_timer for freeRTOS requires configUSE_TIMERS...
Hi everyone
I'm doing some basic test to verify the correct platform for a future project, we need ble long range, therefor we are testing the NRF52840-PDK
I have loaded...
hello,we use nRF24l01+ for the communication of IoT.There are a lot of terminals work at a same channel,when the controllers send CMD,we have found:the length of reading from...
Hello,
I am having a weird reset behaviour with my nrf52832pca10040, SDK12.2 with softdevice v3.
I have connected an acc into the SPI interface through these pins
...
Dear friends,
I want to measure the current of RF of BLE using PPK. However, i do not care the current of other peripheral devices, such as timers, pwm. How can i make it...
Hi,
We have nRF51822 acting as a central and another nRF51822 acting as peripheral. The peripheral advertises at 1 second advertisement interval. The peripheral and central...
Hello,
There is a characteristic with properties:
memset(&char_md, 0, sizeof(char_md));
...
attr_md.vloc = BLE_GATTS_VLOC_USER;
...
char_md.char_props.write = 0;...
