Hi,
We’ve designed a project using the nRF5340 + nRF7002 combination, with Wi-Fi connectivity enabled.
As part of our preparations for FCC certification, we’re currently...
working with a nrf52833, soft device 140.
I am trying to setup a whitelist with a known addresses before I start scanning. I am calling the following code before my main...
HI,
I am using the NCS V2.9.0 ,nrf Desktop sample;
I want to mouse can pair 3 hosts, and i can select one of them connect and work;
I set CONFIG_BT_MAX_PAIRED=3 and...
I have a custom nRF52832 board with outputs on P0.07 P0.08 P0.09 P0.10 and I want to write to them. 7&8 are working ok but 9&10 are not.
Let me emphasise THE BOARD IS WORKING...
Dear Nordic and community,
I am currently in pre-production phase of designing a PCB based on the NRF9151, and I am a bit confused by the Hardware Device Guidelines, which...
Hi Nordic engineer
I am evaluating a project based on nRF52840 and there is a question need to be confirm before schematic design start.
Due to limitation of power resource...
Hello everyone,
I'm trying to set up the Wifi stack on the nRF7002 and use it with MicroPython, but encountering a lot of difficulty with it. I cropped up a network_wlan...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
Through a few days of studying, I now decided that: (please correct any statements I said wrong below)
The BLE is more friendly to object oriented programming
...
I've been a little out of the loop. Can someone explain how this "drag and drop" DFU is working? And in what method iTunes is being used!?
Best I can figure iTunes is being...
Hello everyone. I am having problems using the interrups when a bootloader is programmed on the chip. My test program works fine when there is no bootloader. With the bootloader...
Hi,
I try to turn off the advertising after the first connection and then turn it on after pressing the button, this is what I wrote:
void radio_notification_evt_handler...
Hi,
I've been digging through a lot of AN's about how to design a PCB antenna, in all of them an important parameter is the output impedance of the transmitter.
So,...
Hello,
I'm pretty much new to NRF development and I'm having lots of questions trying to get a custom board to work with the provided BLE bootloader example in SDK 11....
Hi all,
Hi I am implementing MQTT client on the Nrf52 MCU, as to the MQTT broker, I am going to use the amazon AWS IoT , where the broker adopts the TLS 1.2.
I read...
I am using nRF51 and latest s310 softdevice (3.0.0) and latest SDK (v10), which is the latest compatible with the softdevice.
My device is programmed with the softdevice...
Hi,
I'm designing a 2 layer flex PCB with the nRF51822-CFAC WLCSP package and recommended ST BAL-NRF02D3 balun and on-board PCB passive antenna (not ceramic chip antenna...
Hi Friends,
I am using nRF51822(S110 and SDK10.0.0) in my project and I need the chip to be in connectable and advertising mode under peripheral config . I configured the...
Hi,
I have migrated application with freertos (S132 /NRF52 devkit ) from SDK 11.00 to SDK12.00 .
Flashed SD 3.00 and then application ,but Application is not able to boot...
Hi,
Is this the right way of reading the timer value using the capture task. In this code i am trying to read the updated value of counter for every event generated in...
Hello;
I'm developing an application that advertises as a connectable peripheral. As such, it has an ID (think of it like a beacon minor).
I have 2000 of these devices...
