Hello,
I have made a PCB has 4 buttons and touchpad, now I want to drive all of them.
1. one button for left button of mouse. 2. one button for right button of mouse....
Hi! I’m currently implementing a hook using mcuboot_status_change() inside MCUboot. I’m following the path defined by CONFIG_MCUBOOT_ACTION_HOOKS , and I’ve confirmed that...
Hi,
I'm working on a customized version of the nRF Desktop App running on an nRF5340 . In my use case, I want to connect Bluetooth HID devices (mouse and keyboard) as input...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Dear All：
My NRF24L01+ use Dynamic PayLoad,What register need configure NRF51822?
NRF24L01+ Configuration as follow:
SPI_RW_Reg(WRITE_REG + DYNPD, 0x01);//Enable...
Hi,
I've been using the ble_app_uart example as a template for our use case. It is a good starting point. We don't actually need UART functionality, and we've assigned...
Hi,
during programming, we receive error as in this question . The hex files do not overlap.
It seems to happen only when the board has already been programmed before...
Hi,
I have an application that requires watchdog to run continuously. And from application I have code that jumps to the bootloader without device resetting using bootloader_util_app_start...
Hi,
Side effect of adding a LFCLK of 32.768khz with 90k ohm ESR oscillator? where as data sheet recommends Max value of 80kohm.
Side effect of adding lower drive level...
Hi everyone,
I activated softdevice writing protection with nRFGoStudio (i.e. so that the softdevice can not be overriden). How can I deactivate that again so that I can...
Just to make sure: Will The spi_master_send_recv return when it is done writing and reading, or do you have to have some event wait functionality listening to SPI_MASTER_EVT_TRANSFER_COMPLETED...
I was playing around with the gpiote example under exaples/peripheral/gpiote. The example uses a timer, ppi, and gpiote to blink an led. By default, the app uses Timer 0 and...
Hello.
How to write custom firmware updater, which:
Takes new firmware from other device on SPI or I2C bus.
Writes it to flash ("bank1" at 0x1B000, or...
Hi;
I'm studying on SPI communication at nRF51822 (not DK) but i could not find the pins for spi communication, i read at somewhere SPI is only used at DK(developer kits...
hi
i'm using the nrf15822 beacon for an application of communication on arduino
I just would like to understand how i should start to stream my data using the beacon beacause...
Hi all,
I am using S130 in scanning mode and I would like to list the devices that are currently advertising by their friendly name. I have access to p_ble_evt via BLE_GAP_EVT_ADV_REPORT...
Hi,
I usually use electronics.stackexchange.com/.../15143 approach for decoupling capacitors and until now I had much better EMI performances.
I make sure that tracks...
We would like to reduce the attribute table size a little to increase free RAM. Are there any guidelines explaining how we can judge how large the table needs to be for a...
