Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
I am trying to send data obtained from my sensor (calculating with twi scanner example ) via BLE using the ble_nus_data_send function. I just tried to send this data via UART...
Hi,
The eddystone example enter to connectable mode by press a button, but our customer don't want to press button one by one, they hope the beacon can advertise eddystone...
Custom nRF52 device uses SPI interface for external flash, so in order to read/write to external flash would need a RAM loaded firmware to keep code in internal flash untouched...
Hello,
How can I have two or more temperature probes reporting using the ZCL library?
Imagine that I want to have a device that measures for instance two temperatures...
Hi,
I am trying to measure the current of a custom board using PPK board, My custom board takes 5 Volt input supply but PPK board has a 1.8-3.6 Volt external power supply...
I am trying to modify the nRF52840dk_nrf52840 spi_flash sample, ncs/zephyr/samples/drivers/spi_flash , to use dual QSPI.
Following is my device tree configuration:
I...
I am able to pair a peripheral device using advertising 16bit UUID to the Central Device(nRF52840-DK board).
Also I am able to read the Battery level service and Device...
Hi, I have successfully achieved the OTA DFU function on nRF52805. This is what I can see now:
Step 1) I can see the Nordic_Buttonless BLE signal. After connection, there...
When using the nordic power profiler for the nrf52840, it gives the "idle" current as 2.7uA. Presumably this is the deep sleep current, but it seems like this number doesnt...
I've been using nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 for my development. I'm trying to switch to the nRF connect SDK. I'm having a hard time figuring out where to...
Hi everyone,
So Im trying to modify the event handler of the ATT_MTU example file to have it so that it logs every time a byte is sent / instead of KB but for some reason...
Config options for enabling SDHC card support are not working with nrf SDK V1.6.0. Unable to create the project using Segger IDE.
The same options are used with nrf SDK...
Hello,
We are switching our firmware from the old sdk into the NRFConnect zephyr sdk and I cant see any way to retrieve the channel of the advert when scanning. We need...
Hi everybody,
i've got an issue i want to discuss here. I'm building a webserver using the nRF9160DK with ethernet-shield from PHYTEC and an SD-card which holds the frontend...
