Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi,
I am not yet familiar with NFC.I s it possible to read battery data from the NFC tag of the nRF52 to another device (for example a smartphone). I want to write simple...
Hello,
I am in the process of designing a new custom board with the nRF52832. Apologies for the silly question, but swimming in the documentation at the moment, and I need...
HI, we want to develop DFU over NBIoT network (UDP), and we would like some advice on how to implement that. We are using nRF52832.
Looking at your SDK examples for BLE...
Hello Everyone,
I am trying to integrate LIS3DSH accelerometer with nRF52832 development board(I2C communication). I have Implemented Wake-up State Machine for LIS3DSH....
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Hi folks,
I've found no beeter way of reporting this (no public SDK repo which allows issues with code reference).
I tried to TX ESB DPL frames from an nRF52840 to different...
Hi all,
I want to sell a device that I have made that uses the nrf51822 and the app inside the chip is derived from the ble_app_uart. It uses two chips that communicate...
When I send my app to people, it uses a specific version of pc-ble-driver. I would like to make sure dongle used was programmed with the hex file package with this specific...
Hi,
I'm having issues with my nRF9160. I followed the steps under "Getting started with development", but I keep getting the following error when updating the mfw:
I...
Hi
I'm using the NFCT peripheral of the nRF52832 Rev. 1.
The state machine (figure 118 in PS V1.4) shows that the NFCT can be activated by either issuing the TASKS_SENSE...
Hi ,
I am using the secure bootloader example (SDK 15) as a template for my DFU solution.
I am experiencing issue with the update process as the device shuts down after...
Hello
In our project we are using NRF52840 SoC.
Up to this point NRF52840 chip is used as BLE module to be able to connect our device to cloud over gateway.
now we are...
I have added DFU service in my custom application and I am able to upload the zip file of my application over the air by connecting to the DFUTarg using nrfconnect in my mobile...
I'm developing the PCB schematic for a system using the nRF52 and have some questions on the SWD programming interface.
It seems that I only need 4 pins for the Segger...
Hello,
I am curious, does nRF52832 support USB Type-C in terms of data transfer and Power Delivery? Or will I need another MCU to handle data transfer and Power Delivery...
