Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
1. I try DFU bootloader with OTA, it success.
2. But the Application was gone.
3. If item 2 is real, is that I have to porting the force enter to bootloader mode by botton...
Hi!
I am working on NRF 52840 Controller and Soft Device Version 6.0.0. Coding using Keil IDE in C.
Also developing using Free RTOS.
According to the requirement I need...
Hi,
My development environment is sdk12.3 s132_3.0 pca10040 I want to increase the MTU size to 64 bytes in nus. I programmed as below, but there is no MTU size change. It...
I have been trying to configure a single shot timer as a low power alternative to nrf_delay_ms().
I have my timeout handler configured to do nothing and the timer is created...
Hello all,
I have an ESRPB switch from EnOcean which uses the PTM215B transmitter internally.
I've factory reset the switch to its default state and have confirmed that...
After a few notifications in short succession this code will reliably get stuck in an infinite loop (15.2.0). Can sd_ble_gatts_hvx not be used in this way? Do you have to...
Hi
Struggling getting Directed Advertising to work - I have been through all the examples and have been using the ble_app_hids_keyboard_nfc_pairing example.
My NRF52832...
Good day!
I'm working with electronic part of quest game wherein every player has a "player device" (A) and a various amount of "additional devices" (B).
A is multilink...
I am using ICM20649 evaluation board with nRF52832 interfacing SPI connection. I was able to successfully communicate icm with mcu and get data of accel/gyro on Segger RTT...
We have a discovery issue that seemingly only happens with the Samsung Galaxy S8.
We are using the nRF52832 with SoftDevice S132 v2.0.1, and do directed advertisements...
Hello, I currently use the uart-ble-central example with the 6.1.0 stack. I would like to make two changes. 1.) In the case of received data via Uart, the board jumps directly...
Good day all,
I am trying to build a very simple UART connection between the nrf52840 DK and my computer through a UART dongle.
First, I saw the UART example in the peripherals...
Hello everyone,
I am trying to make a program that makes work a stepper motor 28BYJ-48, my stepper motor is well connected to the ULN2003 and the ULN2003 is well connected...
