Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
Hi, I'm using nrf51822 and using SDK12.3 ble_app_uart.
My purpose is sending data using BLE module like this:
Custom Board -> BLE Module -> Android Phone.
It works...
Hi,
I am using 2 nrf51822 devices. one is central and other one is peripheral. I am using s130 softdevice.
When i was trying to connect NRF51822 to other nrf51822.
i tried...
Hello All,
I am working on nrf52840 trying DFU OTA by following steps provided in this link github.com/.../ota-prog.md . where they have mentioned to install python all...
Hi Nordic,
I've used a GPIO of the NRF52832 to drive a FET circuit which latches off the battery, however as the board voltage collapses I see a short pulse on the GPIO...
In single bank mode, need upgrade bootloader by DFU. Performing below procedure, APK shows "transfer complete". Application on target device is disappeared, but bootloader...
Why does the nrf connect app on Android need my location services enabled for it to work? I believe that is the case for most (or all) of the nrf apps in Android.
Hello,
I am using nRF SDK 12.2.0 , with nRF52832 on pca10040 hardware, and working with the example in examples/peripheral/spi/main.c to develop a driver for LIS2DE12.
...
I've read as many posts regarding changing the ble connection interval as I can find but so far have been unsuccessful changing the ble connection interval.
Below has been...
Hi all,
Does in any chip with some constellation (different SD) the device allows less than 7.5ms for the connection interval? Or is this value the absolute minimum?
I am trying to connect to a peripheral device advertising f0000000-0114-4000-B000-000000000000 as the UUID. The peripheral adds it to the stack via sd_ble_uuid_vs_add after...
Hi,
I am using ESB in one of our current projects. I have two devices: one PTX (master) and one PRX (slave). The slave may want to send some data to the master from time...
We have an nRF52832 and an MSP430 on a custom board. We would like to program both the devices using SWD interface.
Would it be possible that both these devices can share...
Hi,
I have an nrf51822 ( variant AB) and I am trying to program a simple ble app beacon example on it.
But I am failing over and over. After searching , I found out that...
Hi,
I am using pca10040 board with s132 softdevice. I have integrated BLE_APP_UART service with BLE_APP_MULTIROLE_LESC example. The device will start advertising when command...
