Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi
Seems like all new nRF DKs shipped with nRF5340 as interface mcu have limited speed on Debug Out.
nrfjprog -r --clockspeed 646 Applying system reset. Run. nrfjprog...
I need to send a JWT to a non-nordic server. They ask for a small struct to be encoded and sent as a string in a larger MQTT message. For example:
That struct is encoded...
I have flashed the light_ctrl hex file in nrf52840 dongle. Flashing Have been completed sueccessfully for provisioning in nrf mesh application its not showing in the network...
Hello,
For a Uni Project I want to measure the current of the Nordic Thingy:91 and visualize it. Therefore i bought the Power Profiler Kit 2. But i dont know how to connect...
So when changing the hci_icp.conf settings to have the configuration below, i get "CMake Error at C:/ncs/v2.6.1/zephyr/cmake/modules/kconfig.cmake:358 (message):" plus the...
My device is peripheral. I added a few lines before the advertisement start in main(). The whole project is in main and simply advertise and get connected and bonded.
...
I want to configure the ESB and nRF21540 chips on the NRF21540-DK. In order to compare the signal gain, I used the nRF52832-DK and burned the Bluetooth routine (without any...
Hello,
I have a project working on Nora B1, which I am testing on nrf5340DK. It is based on the Peripheral UART Sample, programmed with nfr Connect SDK v1.9.1. Now I need...
Hello,
This is probably a dumb question but, I'm having issues with an initial prototype for a product that has been given. The hardware engineer (me) designed and got...
Quick Start can see the board - but says 'Not supported yet'
Load the programmer and select my board: The log looks like this:
19:07:18.801
Initialising nrfutil...
Hi everyone,
I am testing modem shell application (2.6.1) for PPP support.
Here I am building the application using overlay-ppp.conf and ppp.overlay files.
after flashing...
Hello,
I am currently developing a product that is based on a nrf9160 and more precisely with a Thingy:91, this project integrates the tools of Golioth to communication...
Good morning!
I already looked at other questions in the forum but couldn't find any help. I'm trying to implement an example of Https with basic authentication on my nrf9160dk...
Dear sir:
The DAC private key is generated using P256, and the key length is 256 bits, which is 32 bytes.
As below link, why is 68 bytes planned in the factory data? ...
I'm following Intermediate course lesson 1 exercise 2 to use guiconfig.
When I try to open guiconfig,the output in terminal as follow:
How can I fix it?
