I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I am currently updating from SDK v2.3.0 to v2.5.2 but I am not able to get the 'psa' functions working correctly (as they did with previous SDKs).
I am trying to...
Hi, How to find out what function is being called, when sw interrupt occurs? I have created a timer that should call a function. But I'm having a hard time finding what function...
Hi,
I am working on custom board which has nrf9160 as modem and stm32 as host controller.
here I am used lwip stack on stm32 controller to get the IP address.
I have...
I'm trying to integrate AES-128 (ECB mode) decryption into my project
I've based it on the AES_CBC sample, and adapted it to use ECB mode instead of CBC. When I compile...
Trying to use the nRF Connect quick start with the evaluation board and the programming fails. 2024-05-22T09:09:27.145Z INFO Initialising nrfutil module: device 2024-05-22T09...
Hi,
I encountered an issue from my custom board who are using a nrf52832.
When i place my board in very cold temperature environment (around -35°C), sometimes the voltage...
Good afternoon,
I am trying to use a function generator to send a sinusoidal function to my nRF7002 DK and I am vizualizing the values in Putty. I am sending with a frequency...
im trying to write drivers of max31341 external rtc, where i been able to successfully able to set time (starting rtc also) in rtc and get time from rtc, so not im trying...
Hi
I'm trying to figure out how to manage my memory on the nrf9160 sip. Currently my application crashes on a specific lines where I try to allocate a large C++ string ...
I'm working with the nrf/samples/net/https_client sample for the nRF9160 and am trying to get a better understanding of using the modem's offloaded TLS capabilities vs. Mbed...
Hello everyone, I am creating a project that uses data received from a GNSS module, however I first wanted to do some tests using a NMEA0183 string and PuTTY. I am trying...
Good morning,
I am trying to understand how the bootloader process works on the nRF5340, and working on the excercises from the intermediate course. The target at the moment...
I cannot re start advertising while connected.
this occurs even when i configure BLE_GAP_ADV_TYPE_NONCONNECTABLE_SCANNABLE_UNDIRECTED.
I get NRF_ERROR_CONN_COUNT error...
Paring was successful when using nrf_desktop's default device description configs, but after I modified those lines in "prj_keyboard.conf" of keyboard:
CONFIG_DESKTOP_DEVICE_PRODUCT...
Hey there!
I'm playing around with an nRF91 DK using the serial terminal app (the standard one which is programmed during the getting started guide) and am trying to make...
