Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello,
I just bought a nRF52 DK board (PCA10040, 3.0.0, 3023.22, 1050315142 ). It has a N5340 MCU near the micro USB port, and on the other end, it has a N52832 MCU. I have...
Hi,
I own an nRF5340 Audio DK, on which I successfully run the example audio application .
Using nRF extension for VSCode, I've created a new application based on the...
Now I am using the https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/direction_finding_central/README.html and https://developer.nordicsemi...
Hi folks,
I'm trying to build an application with the CAF, and I'd like to use the sensor manager module, but I've run into a few problems -- any help would be appreciated...
I am currently developing with the nRF5 SDK and infocenter.nordicsemi.com is the best location to find information on this legacy firmware. I am aware that the nrfConnect...
Hi, I have problems with debugging for the NRF9160-DK. I installed the latest VSCode tools (as described here https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.6.99-cs2...
Good afternoon,
I am trying to send some analog data from a function generator to my nRF7002 DK and visualize the output in Putty. I use printk to print the values and I...
Hello.
I modified multi-nus central example to connect with four peripheral devices. I don't use uart at all, I don't need it, I don't need routing, I just send 16B frames...
Hi!
I am confused regarding NUS, L2CAP, ATT and GATT.
We are using NUS with data length extension to communicate between two nRF52840 boards and want to maximize packet...
Hi, here in the documentation ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/config_and_build/board_support/processing_environments.html ) for the latest...
I have been trying to interface the Witmotion WT901 sensor with the nRF5340 using the I2C interface. I have previously run the exact code on the nRF52DK and it was working...
Due to the allocation of Flash resources, only 100KB ROM for the app , and if we use Keil, we will have about 20KB of margin for additional code development, but we have to...
I'm new to Zephyr and have inherited a project that uses the stm32 h747 disco board. The last build shows:
Memory region Used Size Region Size %age Used
FLASH: 363268...
I'm trying to download a largish file (~167KB) via HTTP/TCP/IPv6 but the modem crashes every time around the same point during the download. It's spits out error 122, which...
