Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
Iam using "pca10056_s140_ble" secure bootloader example for my project.
FYI. My project gets its new firmware from internet and stores it in BANK1 memory using GSM...
hi Support team,
customer get samples with 9160, but find out they are not able get pin code.
i searched the spec, and at command +CPIN, it is not able to read out the...
Hi,
I've installed ncs manually following this guide: Installing manually — nRF Connect SDK 2.0.99 documentation (nordicsemi.com) and then set the following environment...
Hi,
I have an application using MCUboot (Only for using with serial recovery. No SMP server running in app).
I enable CONFIG_BOOTLOADER_MCUBOOT and parent and child images...
Hi,
I am using nRF5340 DK + NCS v2.0.0 with nrfx backend for SPIM.
For my application I want to trigger a SPIM1 transaction at a fixed interval. To do this, I set up an...
Hello,
I have an issue when trying to use NVS backend for BLE settings with the settings_storage partition in defined external flash region. As we are doing a multi-image...
I am designing a bluetooth module using the soft device S130 + nRF51822. I intend to refer to QDID80592 and 45222 when purchasing DID for bluetooth. When I checked the ICS...
Hi. I am trying to develop a project that use mqtt connection using nrf9160. Currently using thingy:91 for evalutation board. I am using Mobily Network on NB IoT at Saudi...
Dear Nordic Engineers,
When I plugged in and I opened the Power Profiler App, a pop up required me to update the device firmware.
During the FW upgrade the device flashed...
I am trying to use the DTM example for nRF5340 DK (PCA10095). The example is located at "C:\v1.7.0\nrf\samples\bluetooth\direct_test_mode", but I am facing "NRF_RADIO_Type...
Hello there. I am wondering, if while connection establishment or any other communication event through NFC and BLE the system addresses to NVMC? (Maybe mac address or some...
Hello
I search a way to have a similar project as pc-ble-driver with NRF connect sdk
There is a peripherial with many sensor that send data over BLE and i want to command...
Dear all,
When the provisioner add appkey or bind appkey for the node's model, I want to be informed and run a callback function.
Can I set callback for config server...
Hello Nordic support,
I am using the zephyr\samples\subsys\usb\mass example with an SD card. SPIM4 work on 16MHz.When I check this example on a Windows 11 machine, I observe...
