Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Question on an older chip:
Can anyone tell me if FW originally written for the nRF24LE1E would be completely compatible with the nRF24LE1G? I have an opportunity to source...
Hi,
Device: NRF53
I'm trying to send 3 notify packets in a 15ms connection internal but I can send 2.
I'm using Nrf connect and Zephyr. is there a limit or a define...
I seem to be having weird issue upon initializing qwr module in my .cpp file
NRF_BLE_QWR_DEF(qwr);
Doing so results in a syntax error
#define NRF_BLE_QWR_DEF(_name...
I created a custom BLE service following this tutorial and I am able to connect to the BLE service and write data to it, but ideally, I want to send character bytes as opposed...
Hello,
we are using an nRF52833 for our application with the open serial uart bootloader and MBR programmed in it. What we would like to do is:
1) program the application...
Hi everyone, I'm trying to get the LIS2DH12 driver (SDK v15.0.0) to configure a LIS2DH12 sensor connected to my nRF52 Dev Kit. I've wired the chip up as follows (using the...
I set the publish address of client using function:
Unicast address of sever is 0x0003.
After setting publish address by this function, I check publish address from...
Hello community... I was able to compile the GPS sample and flash an actinius icarus (nRF9160) using the Actinius Programmer once and it said successful. However, checking...
NRF52833+SDK17:
I want to use the saadc to sample a DC brushed motor running current when pwm at rising edge, pwm driving the motor.
I can't understand the real meaning...
Hi, I've been working on SDK v1.6.1 and I just wanted to try the v1.7.0, however some functions on the power management have changed, in particularly:
int pm_device_state_set...
I am encountering a problem with programming an nRF52840 DK:
1. I've installed nRF Connect for Desktop version 3.7.1, nrfjprog version 10.14 and Segger JLinkARM.dll version...
Hi,
I'm using the CLI and have logging enabled. The only way I'm able to see my logging output is if I type "log enable info" at the CLI prompt.
Is there a way to enable...
Hi to every one,
i have some questions, I need to be able to update the device to the new firmware, update to the old version and update to the default firmware. for this...
