I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hello Team,
I am using the OT-nRF52840 source and working on the end device. I want to add the I2C(TWI) support in my end application, but as soon as I add any API it shows...
My problem is similar to this
https://devzone.nordicsemi.com/f/nordic-q-a/64696/projects-for-writing-into-flash-memory-does-not-work-on-nrf52840-dongle/264746#264746
except...
Can a "Pin Reset" recover the nRF52810 part if the part has encountered a slow voltage rise, greater than 60 ms, from 0 - 1.7V (described in the image below)?
Hi, I am new to nordic and zephyr and I have a sensor (Melexis - MLX90641) and I would like to test it on a custom board using nRF9160.. I add the sensor into the dts files...
When I open the nrf connect sdk project, it goes like this,
How can I fix it?
Creating solution direction_finding_connectionless_rx.emProject cmake -GNinja -DBOARD=nrf52833dk_nrf52833...
Hello,
I am preparing to develop a design using the nRF52840 and would like any guidance or consideration for an LDO usage. I have found some previous mention regarding...
At 1Mbps, UART will lose data when receiving. When I set it to 230400bps, it works well. I looked at the SDK code and found that too much time was spent in the receiving code...
Hi,
I had asked a question here few months back, about the maximum RSSI that can be seen on the nRF52832 chip.
https://devzone.nordicsemi.com/f/nordic-q-a/73578/maximum...
Hello.
We have several of our own manufactured boards, containing the nRF9160 cellular modem chip.
We use it for HTTP and HTTPS connectivity, on an application based on...
Hello. We are developing using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I'm looking at how to encrypt a string with AES CBC. Below is the code we are considering.
Currently...
Hello.
I'd like to split an external QSPI flash chip so that part of the memory is accessible as raw blocks, and the other part holds a filesystem such as fatfs. Essentially...
Hi
I am using NCS version 1.5.0, I need to drive the GPIO pins of NRF5340 DK using the below library
"#include <nrfx/hal/nrf_gpio.h>"
While trying with this header...
Hello,
I am trying to run the example projects "ble_app_uart" in SDK17.0.2 on nRF52833DK, following the guide shown here: https://infocenter.nordicsemi.com/index.jsp?topic...
