[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
Hi Nordic,
We have done some research on the DHT22 and the results showed that this sensor has excellent performance. Sadly it appears that neither the nRF9160 nor Zephyr...
Dear Nordic Team,
We have a problem in our project with custom PCB regarding DFU. It happens in most of our prototypes, but on some devices it doesn't happen.
Below...
I would like to self-provision my smartphone. Do you know how can I do this?
Then, I read that a smartphone must connect to a proxy via GATT bearer (hence a connection)...
I am new to nRF SDK. I am starting development for my nrf52810 based board. I am using blinky example from nRF5 SDK. I am using nRF52 DK board to flash and debug my nRF52810...
In our setup we are sending one CoAP message every hour. The transmission is set to be done at hh:00. Downstream communication is only required as a response to the upstream...
Hi, My name is Philex Fan who is a researcher working in academia. I am working with a group of researcher to develop biomedical device that can get brainwave signals and...
Hi!
This tutorial is just for current > Measuring current . I want the same for latency with code.
I'm working with two nrf5340 for Bluetooth low energy and I want to...
Dear Community,
From a provisioner, I want to get the MAC address of a device (provisionee) during the provisioning process. Is there an example somewhere in the forum please...
Hello,
I am using nrf52805 processor, nrf sdk v16.0.0 and Segger embedded studio. My board communicates with a temperature sensor over I2C. The software is working without...
Hi all,
I am working on a ble5 beacon with ecdsa signature. I would like to use mobile to verify my message. As I see that the crypto ecdsa example use raw key and generate...
I have developed an APP using SDK 15 (both BL and APP) updating Bootloader and APP which is working fine.
I have developed same app using SDK 17.0.2 (both BL and APP)
...
Hi, I know this topic has been up in several posts before, usually ends with, buy a LitePoint or Anritsu.
Assuming you want to do a poor mans measurement setup, just relying...
Hello, I've been trying to get the nrfx_i2s driver working with Zephyr, on the cpuapp core of the nRF5340. After configuring the driver, setting CONFIG_NRFX_I2S in prj.conf...
I've been successfully creating custom services, but there is one case where a device has a service UUID and it's 2 characteristics have completely different UUIDs (all 128...
Hi,
How do I set ncs v1.5 to save the last open project path?
ncs v1.3 has the last open road
ncs v1.5 does not have a project path that was last opened
Here's the...
