Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello,
I would like to take a photo and send it via Zigbee to another on nRF52840. Just a single image that is around 600x480 sizes. What interfaces can I use for that purpose...
hi,
i am including spi in ble_uart program .i am getting error "'NRF_DRV_SPI_INSTANCE_0' undeclared here (not in a function); did you mean 'NRF_DRV_SPI_INSTANCE_'?".
Hello,
I have joined a team that is already in development of firmware for their nRF52840 based product. The team has a Git repository that includes the SDK which I have...
I am using nrf52 and there is a sensor connected to it. I want to read the values from the sensor and sometimes this is changing fast like 1-10 ms. The idea is to connect...
Hi, i got this following error. Kindly help me in solving this.
C:/Program Files/SEGGER/SEGGER Embedded Studio for ARM 5.40c/gcc/arm-none-eabi/bin/ld: cannot find ../.....
Currently, I am using the ble_app_cts_c example and I want to disconnect the connected device.
I want to know how can I check the condition for any connected device?
and...
Hi.
i am using NRF52832 DK with MESH SDK
can i transmit string from Low Power Node to Friendship node.?
If yes kindly let me know what changes i need to do for that...
I have observed two issues with using the UART in an ncs project and I'm not sure exactly where the issue lies (Nordic or Zephyr).
Firstly, and most importantly, according...
hello Nordic
i am using nrf52840, sdk 16.0 working on ther peripheral ble_blinky example, working with Segger IDE (ses)
i have lines of code missing when i am debugging...
HI,
I am trying to connect multilink central to multiple peripherals. I am able to connect using "target name". But i dont know how to connect using central to peripheral...
HI,
Currently, I am using the ble_app_cts_c example and I am able to pair only one device. I found out that it is related to whitelisting function.
How can I disable the...
On SDK16.0.0 + Mesh SDK 4.1.0
I've followed this to add PA/LNA support in the bootloader (Fanstel BT840X). I see the increase in RSSI and know that it is working.
...
Hi,
I am evaluating the Light Ctrl example of the Connect SDK 1.4.2. After nRF52840DK was programmed and provisioned by iPad, Mesh App, I was trying to bind application...
Hi,
I have built the example hrs_uart project and it works fine when I load the image into a pair of OCA10040 demo boards, one as application board and the other as connectivity...
