Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hello,
I just solved the previous problem thanks to the reply. Thank you a lot.
But, I have one more question..
I was tested UART central example( ble_app_uart_c)...
Hello, I am working on a firmware for nrf52832 custom board, whose purpose is to light an onboard LED if another nrf52832 custom board (same design) is near to it. The other...
Hello,
I am developing a zigbee coordinator with a BMD340 module (using the nRF52840). I want to support several third party device with the coordinator. I am able to connect...
Hi, We have a smart product, which has two application scenarios. One is the use of BLE peripherals, similar to sports bracelets; The other is the 2.4g private protocol mode...
Hi Nordic team
How can I begin to develop the thread mesh? from the https://infocenter.nordicsemi.com/index.jsp I can run which example project
I had no found it from...
Hello .
I want send BLE data of sensor value.
So, I am using the central module(HM-10) And peripheral is nRF52832 of custom module.
Connection and data communication...
Hi
We are working on the FOTA based on http_application_update project. The hardware is Thingy91.
The issue is if we use the default the MCUBootloader on Thingy91(version...
Hi ,
I am working on nrf based project . I m trying to build my project using Cmd . I followed the steps given in link -
https://devzone.nordicsemi.com/nordic/nrf-connect...
Hello,
is it possible to localize the chip via the NB technology.? I red that this is supported by the NB standard.
When I switch on NB supporte systemmode the gps sample...
Are the accepted values of nrf52832 output power as below:
4, 0, -4, -8, -12, -16, -20, -30, -40
What we are most concerned about is whether -30dBm output power was available...
To the kind attention of Nordic support team,
We would like to delete BLE bond infos, only for test purposes. Being BLE not even activated and softdevice not used.
For...
My nRF52840 arrived yesterday and I started playing around with it. It is immediately recognized y nRFConnect v3.5 BLE App v2.4.0. The firmware on the device is 4.1.2 Jul...
Hi There.
I just downloaded a SDK for the wisol module that uses the nRF52832 and i can't get it to compile in Keil V5.31. Im getting this error:
Error: *** Project...
Hi
I am new on nRF52833 and want to try RF test for development.
I have a nRF52833_DK on hand with Direct Test(DTM) in nRF Connect(Descktop). However I am not success...
Dear Sir/Madam,
We are «SMART Solutions», Ltd. a startup from Tomsk, Russia.
Our company developed iBack Posture Corrector please see http://en.iback.online/ .
The device...
