It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
For some reason I can't quite program the nRF9160 on the development board using Segger Embedded Studio (SES) when I create a new project. I must be doing something wrong...
When I set "report_incomplete_evts = 1", I get a NRF_ERROR_NOT_SUPPORTED (0x06) error.
If I comment it out, everything work as expected. I want to use it for exended advertise...
Hi All,
I need to find the RF Tx power setting of the nRF52840 by reading from the register. I understand this is possible through Jlink and the following command:
--memrd...
Hello,
I am developping a project on with the nRF9160 and I would like to have the LTE and GPS working concurently. I managed to have both working separatelly on my custom...
Hi. I am confused about flash endurance. In the product specification for the nRF52832, there is a note that flash endurance is 10000 write/erase cycles:
Does it mean...
Hi,
What's the easiest way to subscribe to the MQTT messages that the thingy91 sends to the nRF cloud?
I have tried setting it up with a node-red and a python client...
I am newbie in nrf51822 and I am going to do project nrf51822 with BLE mesh. I have some questions regarding to this, please support me: Does Nrf51822 support BLE Mesh? Does...
To the kind attention of Nordic support team,
In PCA10059 hardware files C10, C13 and C25 are not conected when I see in the bill of material. But it seems that in the real...
Hi,
I am currently just trying to clone the nRF connect sdk according to the getting started assistent.
All the first steps just worked fine, but I ran into a problem...
Dears?
When I click the download link of nRF Sniffer v2.x ,it show "page not found(Error404)"
Would you help me?
nRF Sniffer User Guide v2.2 is to be used with the...
Hi Sir,
In normal, we can see three virtual COM ports in nRF connect - programmer, first is for nRF9160, second is for nRF52840, the last is for nRF9160 but not use.
Then...
Hi
I have a wired situation in my project. Everything is working fine when I am running my heart-rate device with the debugger. When I detach the debugger or just power...
Hello
A project that recently made a sensor found that the timer consumes a lot of power.
I built a timer to collect sensor data in the timer handler.
Sensor only...
Platform NRF52832 SoftDevice S132 V6.1 SDK 15.0 FreeRTOS implemented
Hi, In our application, once the mobile app is connected to the peripheral, it makes continuous writes...
Hi, I've started an 802.15.4 project using the nRF52811 and see that support in the vSDK 15.3.0 explicitly states the 802.15.4 stack is only for another part. Is there support...
