I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi DevZone,
I have problems with running the coexistence examples from the Mesh SDK. Specifically I’m most interested in the UART coexistence example ( https://infocenter...
Hello all,
I want to enable OTA DFU capability to NRF52840 BLE Chip. I am now using Buttonless DFU which works fine using nrfutil. But my question is : how can we update...
Hi
I'm upgrading from SDK11 to SDK12 on the nrf52 and part of that is the secure bootloader. I've created a new bootloader and have this working with the new softdevice...
Hi,
I tried to open the mqtt_simple project on the nonsecure ns nrf9160 DK using SES and after that tried to build and run the project which was successfully done but the...
Hello,
I'm wondering what are the drawbacks of the already burned random static mac address compared to a public mac address. I know the difference between the two address...
I have Wireshark setup with old PCA10028 board connected as a sniffer, FW sniffer_pca10028_51296aa.hex Now I'm working with NRF52 family and sometimes I need to observe some...
Hello everyone ,
i want one central uart and three uart peripheral , i want to connect the central to all three peripheral , if i send data from central , it should receive...
Hi
I have a problem with showing data packets in wireshark. I configured the sniffer according to the instructions. At capturing packets in main window don't show anything...
I want to use UART.
I checked the waveform and UART does not send data. Here is my code. build and run are successful. Any help? I connect UART RX and TX directly, which...
hi... how to make a nordic app to act as a peripheral , i have read one post , in that they mentioned set up to be done in gap peripheral mode . how to do that
IAR 7.60
52840
nRF5_SDK_15.2.0_9412b96
Hi there, I'm trying to do some modification in the bootloader (so that we can write the image to the flash's bank1 using our...
Hello,
I read through the Bluetooth core specification in order to get a better understanding of the information that has to be stored at a minimum if using bonding. But...
Hello,
i'm trying to use ble_advertising_init to initialize my advertising data, but when i use this function like it is used in the examples i get NRF_ERROR_INVALID_PARAM...
When I open device just after I plug it in the PC it work fine, but when I try to do it again (exit python script and run it again) I'm getting Error code 13.
Firmware:...
