It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
The example projects I am referring to is located here:
nRF5_SDK_15.2.0\examples\iot\mqtt\lwip\subscriber\pca10056\s140\ses\iot_lwip_mqtt_subscriber_pca10056_s140
nRF5_SDK_15...
Hi all,
I successfully ported the Semtech’s LoRaMac-node (from official GitHub, master branch) to a custom assembly of two dev boards : the NRF52832 (Dev Kit PCA10040) from...
Hi,
I am trying to use UART interface on a nRF9160DK board to connect a rs-232 to rs-485 module for the purpose to make nRF9160DK a Gateway.
But I have no idea where to...
Hi,
Are there any known Android bugs where Android should not bond, but does? I have tried searching the web without too much success.
My central device is an older Android...
Hi,
Is it possible to add scan response with extended advertisement packet?
When I try to add scan response, then I got error NRF_ERROR_INVALID_PARAM.
I am using a nRF52840...
Hi there,
I am using two nRF52 one as Master and the other as Slave SPI, but I am facing an issue with the slave side, because when I use NRF_DRV_SPI_FREQ_125K it get some...
Hi,
I am using the nRF52840 on a custom board with SDK15.2.0 with SD S140 6.1.1.
My current BLE connection parameters are below which allow connection to the nRF Connect...
With Mesh SDK 3.0.0 , i have tested with light switch example with one client and one server, it works. My question is is it possible that one server can communicate to another...
Hello,
I have developed simple scanner application that scans for beacons (apple, nordic and of own type). It prints data about beacons over UART. I have installation where...
Hi,
due to some evaluation effort of nRF52840 Dongle, I went through whole Zephyr project building of their Bluetooth hci_uart example. After couple of ardous hours(or more...
Hi there,
To do LESC with some peripherals supporting OOB Rx, and some not, and the central supporting OOB Tx, I was wondering how to correctly enforce the OOB for the right...
Hello,
I am beginner with NRF 52 DK. I am trying to change the uart example using NRF 52 with SDK 15.02, so that I would send message after pressing button to my PC via...
A temperature and humidity acquisition device uses NRF52832, watchdog, RTC timer, external touch button interruption, BLE open state, feeding the dog every minute through...
Hi,
I am having 2 nRF52 DK boards and I have to blink the leds of one nRF board with the help of another nRF 52 DK buttons and vice versa .
How to do it?
