here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
HI:
everyone!
How to make the matching and binding equipment information would be stored permanently, even after the OTA upgrade is still in;I made with examples of the...
Greetings, I tried to modify the parameter "len" to anything over 1 (byte), but it just doesn't work.
As long as it's over 1 byte, the API crashes my program. err_code shown...
Hi,
I'm using s130 as softdevice for nrf51822. I program the softdevice with the official s130 hex file. According to the hex file, there is no data at address from 0x7c0...
We're working on an application that needs ultra-short range BLE, on the order of 50cm radius or less. I've found little discussion anywhere on that topic, likely because...
I notice that the dongle has a 3.6V-5.5V input and a pin that sais 3.3V, I measured 3.3V on this pin so I was curious if I could run an IMU unit and an i2c/spi bridge requiring...
Hii all
I am trying to port the experimental/bootloader_signing project to gcc I made changes in the project accordingly, so now its working. I can able to flash application...
I connect a GPS module to nRF52 DK and connect nRF52 DK to my computer once more.
GPS module ---> nRF52 DK ---> computer. (like this)
So I want to do NMEA parsing like...
Dear All,
I am sorry but I have to ask this question here, I searched and red trough the forum, tried the suggestions, nothing works.
Basically I want to have a HID device...
I use softdevice 6.00, size is 80K Byte. I use the chip NRF51822ab,and configurat the irom start at 0x14000,size 0xC000, IRAM, start at 0x20002000,size is 0x2000 ,in keil...
Hi,
Is there a possibility to read the state of the gpiote pin? (is it high or low). Is there any function or any other way to do that?
I'm changing the gpiote pin via...
Hi,
I made a own service for a rotary dail in a peripheral(S110). This service send the speed, direction and a counter (all uint8) of de rotarydail in separate characteristics...
Hi Everyone ,
We were using nrf51822 rev1 IC for our project and now it is changed to nrf51822 rev3 . Previously we were able to detect the chip in nRfgo Studio on our...
I am looking for a device with support for the 4.2, long packets (up to 255 bytes) feature. I see that the nRF52 is a 4.2 device. But for what I understand the optional long...
I am using s120 for central device, and my central device connects to multiple BLE slaves. After connection, some slaves may lost connection due to power off of that device...
I want send ble bond connection request from raspberry pi to nrf51882.
Can you please let me know which ble libraries I need to send central ble bond request to nrf51882...
