Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi, We are currently migrating our project, originally developed with NCS version 1.8.0, to the latest NCS 2.7.0, while incorporating MCUboot for both of them. During this...
Hello,
I am encountering an issue with the nrfutil settings generate command. Each time the command is executed with the exact same parameters, the resulting settings.hex...
SoC: nrf52840
SDK: OpenConnect 2.4.4
I have been developing an ambient noise system using I2C microphone, nrf52840 and Zigbee networks for some time. The firmare reads...
Hi,
Is nRF52811 / S140 capable of simultaneously being in peripheral (connected slave) and central (connected master) mode like described in this blog post https://jimmywongiot...
I’m working with the nRF5340 and nNF Connect SDK 2.6.1. I’m encountering an issue where, after a central device (e.g. an Android phone) forgets a bonded peripheral device...
There was a previous discussion about the option to disable/enable slave latency a few years ago:
Did this ever get implemented? Specifically interested in the feature when...
SDK: 2.6.1
I needed to add a single wire support to our device recently and I did that by using two pins TX/RX shorted and UART. It works, but current consumption sky rockets...
Hi all
How would I be able to generate and view the calculated hash that i get while using the dfu library? Is there an easy way. I'm hoping to generate one single hash...
I am looking for the code example of how to setup A-GPS/A-GNSS on a nrf9160 dk, but I am not able to find one. I am only able to find these links:
https://developer.nordicsemi...
Hi everyone, I'm encountering an issue with MCUboot on NCS 2.7.0 and my custom board based on the nRF52840. The bootloader was functioning correctly with NCS 2.4.0, but now...
Hello,
I'm using nor flash with qspi as an external storage.
I'm facing problem where i can have different NOR Flash chips (with different jedec-id). Is there a way to...
I am testing ble_app_hid_keybpard of SDK17.1.0 using nRF52-DK board. After running, if BLE connection is not made, it enters Sleep_Mode after slow advertise. At this time...
I am working with the "TF-M secure peripheral partition" sample project ( nRF5340DK, NCS v2.5.0, nrf/samples/tfm/tfm_secure_peripheral ), and modifying it as necessary to...
Hi
I want transfer 200+ KB file from master to sleave , Is there any dedicated service for file transfer in BLE.
or
what could be the best way to transfer 200kb size...
With conventional python virtual environment and Zephyr west, things seems to work well. I decided to give it a try to nRF Connect for VSCode and I observed that it not use...
