Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
I've been testing a sample program to log data continuously on a littlefs file system.
I'm using Zephyr OS build v2.6.99-ncs1 and 125 MB (1Gb) NOR flash from Winbond.
...
When utilizing the 2-wire FEM control within the Network core, is it possible to have a 3rd GPIO output slaved to these two FEM control outputs and preserve timing? That is...
Hi Nordic,
I want to use this example to learn bluetooth mesh, but I cannot find the bootloader source code used in this example.
I used vim to view this "serial_nrf52832_xxAA_s132_7_2_0...
Hey, Our custom board based on the reference circuitry in " Product Specification v1.2 ":
We have been using the B0 revision of nRF9160 so far. Now we are planning on switching...
app_twi_perform() returns 0x03 == NRF_ERROR_INTERNAL.
Reset board with button does not help.
After Power Cycle can update EEPROM successfully.
Accessing FTM buffer with...
Hi,
we have developed our working UART code according to Zephyr documentation, and its working fine,
we find that this code works with EasyDMA . but my question is my...
I am trying to scan for Bluetooth LE devices in Android with Java. Everything worked fine and I released an update and on fresh installs it does not work. I went through every...
I'm seeing an assertion failure at PC=0xa806 in nrf52840 + S140 7.3.0, while using L2CAP.
I know the most common cause for softdevice assertion failures is interrupt/timing...
Hi, I'm using nRF52805 and SEGGER. My BLE device disconnects with the mobile app occasionally. The disconnection happens randomly. In the debug mode, I see some messages....
hi,guys
I have a product that uses CHIP 52832qfaae0, and then I replaced chip 52832qfaae1, and there is A problem. Chip 52832qfaae0 runs normally with the same code, but...
Hello,
looking at the compatibility matrix for the 820 it seems that rev2 of the 820 can be used with softdevices and the legacy SDK v17, while rev3 can only be used with...
Dear Members,
I want to use SPI LCD and Sdcard, they have different CS, but sharing the same SPI ports, I have used different SPI instance but not giving us a good response...
On opening a sample project located at https://www.nordicsemi.com/Products/Development-software/nRF5-SDK with keil V5 , I can directly have an error message “Cannot read RTE...
Hi there, I'd like to make some FIR or IIR filter on my nRF52840 DK. I guess I'm supposed to: 1) Provide .a file into SES project's tree (or as Additional Input File): 2)...
