Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi all
Thanks in advance for any hints you could give on this. I would like to measure two pwm signals (frequency and duty cycle) on two input pins of the nrf52832.
board...
In the nRF5 SDK there are two uart drivers, UART and UARTE. The UARTE driver makes use of the DMA whilts the UART driver uses interupts. This is what I understood when I used...
I am considering using this part from MAXIM (MAX31343).
https://datasheets.maximintegrated.com/en/ds/MAX31343.pdf
it is an RTC plus a 5ppm oscillator output that I can...
Hi all,
Now I'm analyzing the bug that is the fault of my application's timing control.
On analyzing, I found the difference that garbage collection callback was delayed...
Hi,
I am using nRF 5340DK borad, trying to flash Direct test mode sample "nordic,nrf5340-dk-nrf5340-cpunet". My aim is the enable direct test mode on the nrF board in order...
I'm using 3 nRF52840 DK borads (provisioner,light_switch_client, DFU). I set DFU (DFU example used) as target board and connected it to PC as serial interface. I have provisioned...
Hai,
I'm facing some difficulties in programming FOTA over UART on the NRF9160 board.
Currently, by using the following command I'm trying to push the bin file via UART...
Hello Team,
I have a small issue but troubling me since a long time now. Accidently my debug terminal and project explorer came out from their original positioning. Now...
Hi,
I am new to NCS and visual studio. I created an app based on the hello world sample app. And set the break point to the line of the printk in main.c. However, when...
Hello Zephyr experts,
I am having problem with the function wdt_disable(const struct device *dev);
There is no problem in setup and feed the watchdog.
wdt = device_get_binding...
Hello,
My application is a modified version of MQTT_simple.
I have moved all the code inside while(true) to a thread and set username as a device token.
The error -12...
The device has high power consumption when in shutdown, around 0,5mA. It uses SPI and TWI in normal operation but I have implemented the work around according the errata but...
Hello,
In normal C program, if I want to print int64_t, I can use the following code.
But it does not work on nRF Connect SDK v1.7.0.
1. Why it prints %li on the terminal...
Hello,
I am working on a custom program for the Thingy:91 that will use the aGPS as well as LTE to send data to a custom cloud server. As part of this, I wanted to ensure...
