I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
I modified my nRF52840 dongle as is was described here Does anybody have a single diagram showing how to connect the DK's P20 pinout to the dongle ? Thanks,
Matthew
Hello! On 2019-06-24 the following mail was received:
Product update notification June 24, 2019
Hi Bojan,
We've just released a new version of our SoftDevices, version...
To the kind attention of Nordic support team,
Could you please give a very quick look at those attached gerber files? Do you think there is something that is better to correct...
Hi Nordic team support,
I want to test communication range between nRF528xx device that support LE coded with samsung galaxy s10 (support LE coded also)
1. If I configure...
For some reason I can't quite program the nRF9160 on the development board using Segger Embedded Studio (SES) when I create a new project. I must be doing something wrong...
When I set "report_incomplete_evts = 1", I get a NRF_ERROR_NOT_SUPPORTED (0x06) error.
If I comment it out, everything work as expected. I want to use it for exended advertise...
Hi All,
I need to find the RF Tx power setting of the nRF52840 by reading from the register. I understand this is possible through Jlink and the following command:
--memrd...
Hello,
I am developping a project on with the nRF9160 and I would like to have the LTE and GPS working concurently. I managed to have both working separatelly on my custom...
Hi. I am confused about flash endurance. In the product specification for the nRF52832, there is a note that flash endurance is 10000 write/erase cycles:
Does it mean...
Hi,
What's the easiest way to subscribe to the MQTT messages that the thingy91 sends to the nRF cloud?
I have tried setting it up with a node-red and a python client...
I am newbie in nrf51822 and I am going to do project nrf51822 with BLE mesh. I have some questions regarding to this, please support me: Does Nrf51822 support BLE Mesh? Does...
To the kind attention of Nordic support team,
In PCA10059 hardware files C10, C13 and C25 are not conected when I see in the bill of material. But it seems that in the real...
Hi,
I am currently just trying to clone the nRF connect sdk according to the getting started assistent.
All the first steps just worked fine, but I ran into a problem...
Dears?
When I click the download link of nRF Sniffer v2.x ,it show "page not found(Error404)"
Would you help me?
nRF Sniffer User Guide v2.2 is to be used with the...
Hi Sir,
In normal, we can see three virtual COM ports in nRF connect - programmer, first is for nRF9160, second is for nRF52840, the last is for nRF9160 but not use.
Then...
