Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
I did have a working development board. I was working to disable serial and disable as much as possible to get the power usage down. It seemed to be working (although...
I tried this using the ram_retention example from the SDK (nRF5_SDK_15.3.0). The example (Ram Retention) still seems to work if the lines concerning NRF_POWER->RAMON and NRF_POWER...
Hi,
our appliction need to using I2S worked at 96kHz sampling, and i find two parameters , MCK and the CONFIG.RATIO,but when i use this formulation:
LRCK = MCK /CONFIG...
Hello,
I think about connecting two central devices (nRF's 52840) using one common antenna. One device will be only RX and will scan for a advertisements, second will manage...
Hi, I am from China. My company made a BLE module with chip nRF52810. Recently , I coded a program for it by SDK12, based on ble_app_uart example. I modified the corresponding...
I have setup the nRF52840 DK as below
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/how-to-setup-the-thread-demo-displayed-live-at-google-i-o
Setup WireShark...
Hi,
We are currently going to try and implement FOTA/DFU with an nRF52840 controller and an nrf52832 peripheral. Is there any example for how this can be accomplished...
Hi,
I currently have a nRF52840DK pre-programmed with the DFU over BLE, but with the debug version. I am unable to physically get to the device, if I wish to perform a...
Hello,
We are using the SPIS on the nRF52832. We are seeing a higher than expected consumption when it's enabled and not used.
I measure around 7uA extra when enabling...
Hi:
I test the system off mode, I attached a micro vibration sensor. Pulse generated when shaking as follow.
the button config is BSP example default(toggle) , i try to...
Hi,
I am testing the blue_app_uart example and I want to send data
from my smartphone uart terminal app,back to the nRF52840 DK,
Nothing is being received by the segger...
In the latest Mesh SDK, nodes are subscribed to a GROUP address. In previous versions - 2.0.0 I believe - you could also send to a predetermined node.
I am trying to figure...
Hi I am reviewing the nRF52840-DK hardware documentation to make boards with good antenna performance.
Q1. I have divided it into three areas as shown below. Is my understanding...
Hi,
I have been trying to use Keil MDK's Middleware File System with my application. However, when I try to set the Software Component under Manage Run-Time Environment...
