Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi
Newbie in the nRF family of products so i might have missed the answers to my questions somewhere in the documentation and forum. if so i apologize.
I'm trying to get...
Hello ALL,
I have been using UART module and fstorage module in an application. I've been sending a bin file from PC to NRF52 using UART but when I tried to save it using...
Hi All,
I have some code that I'm porting from a Zilog platform over to the nRF52 platform. The code uses 1 timer and 1 uart. The goal of the code is to handle RS485 messages...
I am testing the IoT_lwip_MQTT_publisher_pca10056_s140 example project from SES on Windows.
I build and install the kernel with 6LoWPAN module on the Rpi3!
I can run from...
Hello，I'm from China。
At present, there is a need to broadcast beacon data in nrf51822 (SDK_12.3.0_d7731ad is used as the protocol stack version, and the...
Hi
I want to generate two PWM signals that are phase shifted with 90 degree, with similar duty cycle. I have the following pwm configuration, but I don't know how to proceed...
I am operating as a Central. How do I register and enable a discovered characteristic's indication?
I do the following and the subscribe passes but then the kernel crashes...
I'm planning to buy a nRF51822 based module for my BLE project & I wanted to know whether any of the nRF51822 based modules come with OTA ready bootloader out of the box....
Hi,
I'm trying to save sensor data to sd card on low power mode. When i connect to bluetooth mobile app can pull all data from sd card.
How can make this architecture...
Hi,
I'm using Nordic BLE Sniffer. When I look into the captured data I see a lot of malformed packet (CRC error). It try to decode any received data even if there is CRC...
I was digging around a bit in my code to get a better grip on logging. In sdk_config.h, I have the following relevant settings:
My modules all implement their own logging...
I am going to implement DFU over BLE in my nRF52832 project. Since the size of my application + softdevice larger than half my memory size I wonder how the update is performed...
We're looking to use the nRF91 to measure the LiPo battery voltage to determine battery health. We would want to know what the accuracy and range of %XVBAT is. Looking at...
I am trying to create CTS server using nRF 52840 dongle and nRF Connect PC app (v2.6.1). Currently I can manually provide current time and local time information to the app...
