Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
I am trying to detect when mtu has been successfully negotiated through the ble_evt_handler function, which is passed into NRF_SDH_BLE_OBSERVER as shown below:
// Register...
Hi - I'm trying to program the Thingy52 using my nRF52840 DK and Macbook Pro. I've got the Thingy connected to the DK via the 10-pin cable. The first time I ran nrfjprog on...
Hi there!
I have migrated ble_mpu_simple from sdk14.2 to sdk 15.2.
I use Keil uVision to test "nRF5_SDK_15.2.0_9412b96\examples\nRF5-mpu-examples-master\nrf5_ble_mpu_simple...
Hello,
Let me start off by saying that in our use case we are transferring large amounts of data (megabytes) through BLE. This works fine on iPhone 6s+, iPhone SE, iPhone...
Hi,
We're looking for a Bluetooth chipset / module for a Android Pad hardware.
Given that Android 8.0 BlueDroid stack requires Bluetooth chip support HCI commands, is...
Dear all we are using nrf52810(48pin).we did not find exact solution about how many i2c and spi available for that.in which pin we have to connect i2c device and SPI devices...
Good day!
How can I calculate the maximum throughput for BLE Mesh running on the nRF52832 and the S132 without packet loss in ideal conditions?
I have tested throughput...
I notice that for everything related to a BLE connection in the nRF code, there is a "connection handle". Usually, the handle is zero. When is the connection handle NOT zero...
I have successfully worked out the Light Switch Example in the nRF Mesh SDK v3.0.0 using nRF52 DKs. I used the nRF Mesh app for provisioning. I want to know what is the next...
Hi
I am using nrf51822 AC custom board and willing to program over dfu.
For dfu service setting I referred following links. Only change I did in pca10028 library because...
Hello, I'm working with the pca10040e version (s112) of the nordic UART template example. I want to read 20 values from the SAADC, average them, then take a TEMP reading,...
I use nRF52832, with nRF5_SDK_13.0.0_04a0bfd, with s132_nrf52_4.0.2_softdevice.hex, IAR IDE for ARM 8.32.1 on WIN10
I created three services with each having a characteristic...
Hi!
nRF52832, SDK15, SD6.0.0, S132
I try to use secure_bootloader from SDK15 examples. All works.
Now I need encrypt my firmware with AES. I already made it on a SDK13...
Hello
I am about to build a BLE central to open a motorized garage door (runs on solar power) with a smartphone. I am going to design a PCB for this.
However, I am an...
Hello,
I have an BLE application running on nRF52840 Dongle, and I develop an iOS app to control the Dongle.
Now, my work is to make Dongle passing the FCC Testing....
