Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hi,
I'm working with the nrf52840-DK and using the nRF5 SDK v15.2.0 Stack version.
I´ve got a working program for my coordinator (C) and my end device (ED). The C establishes...
hello dear, is there any pre defined function or library in segger embedded studio for I2C interface..? i want to make communication with digital temperature sensor(MCP9808...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Hello.
I need to solve this problem urgently.
I have now created my own protocol and are testing.
At the point of this project is the guarantee of data transmission...
Hello All,
I am developing an application using Nordic nRF_SDK_15.0.0, in which I need to make my BLE peripheral device as a peer device which will get/set data from/to...
Hello,
I am developing application for nRF52832 based SoC using nRF_SDK_15.0.0. I need to develop number of custom characteristic using given sdk. For reference, I am using...
Hello.
I'm trying to understand how to programm my nRF52 DK (PCA10040 - Rev 1.2.1) with SEGGER Embedded Studio (in Windows 10 - x64), however I can't follow all the tutorials...
Hello, environmental engineering is D: Lianxi nrf522 nRF5_SDK_15.2.0_9412b96 examples ble_peripheral ble_app_buttonless_dfu
You can't run this ble_app_buttonless_dfu after...
Hello，Connecting the Nordic_Buttonless device in NRF connection did not see the DFU
Using nRF5_SDK_15.2.0_9412b96\examples \dfu \secure_bootloader\secure_bootloader_ble_s132_pca10040...
Hello All!
I have a question regarding Bluetooth. What is the best way to get data from 200 low-power bluetooth capable devices?
Assumption 1: All of them will use nRF52832...
As mentioned on https://devzone.nordicsemi.com/f/nordic-q-a/35771/nrf52-mesh-dfu-questions , NRF_MESH_SERIAL_ENABLE 0 should be set on devices that receive firmware over Mesh...
Hi,
i have a custom board with nRF52832 and temperature sensor in it.
my question is whether i can read the temperature from sensor via I2c when the device is in sleep...
Hi guys,
I met a problem here and hope anyone can help, thanks.
We bought some unique mac address from IEEE and want to flash them into nrf52832 permanently. The nrf52832...
I'm in the process of adding mesh support to our existing application and am a bit perplexed as to how best implement NVM. The mesh SDK documentation dissuades me from continuing...
