I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello, I am trying a simple btle application where one mcu will send a "help" message and another will respond with its address. The mcu that asks for stores the address of...
Hello,
I would like to implement the nordic DFU protocol natively in a new app as I have historically found it tiresome and buggy to turn the DFU program into a library...
Hello, I am using eclipse app development, to achieve OTA function, use Maven to download DFU library, can not find the library, see your introduction： compile'no.nordicsemi...
I have a BLE circuit utilizing an NRF52832 cpu/integrated radio, necessary impedance matching network and a single ended micro-strip "L" antenna. How can I determine the gain...
I an trying to wake the chip and record the temperature readings when temperature reaches a certain threshold (eg: 80 deg C), can this be achieved using built-in temperature...
I debug the DFU Bootloader through UART,I am sure the APP code is complete updated,but the application does not run when the device is after bootloader to auto soft reset...
Hello:
I'm trying to get an example program ble_app_hrs running on my custom board, because earlier last month I couldn't write the cccd descriptor properly and I suspect...
i try to connect and read and write on my device with ionic2 BLE plugin , i can connect and also write on the device but when i try to read a data from device and use startNotification...
Dear team,
Our customer using "nRF51422 Development KiT8PCA10028)" with "ble-sniffer_nRF51822_1.0.1_1111_Sniffer.hex".
They can check advertising packets, but, they...
Hello,
Here is a newbie question:
I have NRF52832 (sparkfun breakout board) and ADT7410 temperature sensor and, I want to create a data logger. But, i could not understand...
Hii all,
Is there any one started using and succeed with nRF connect 2.0, I installed and open this app, and added two apps two this
After that I launched the app...
hii team,
iam trying to pair my central app with one peripheral device which is generating random passkey while pairing .when central (my App) is sending pairing request...
Hi,
I am using the pin change interrupt example provided in the SDK examples. By setting the input sense to NRF_GPIOTE_POLARITY_LOTOHI, the interrupt handler is called...
Hello, i am a beginner, i have a doubt that my UART project is building without the softdevice being flashed and the output is not seen on the pins. I wanted to configure...
Hello
I want to change the mac address of my device from normal mode to random mode,
I do not know how this does for nrf52832 (NRF52-dk)
Thank you in advance for your...
