Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi,
We are having issues with getting the output power of +23dBm when using the nRF9160 DK in CW mode.
We use the following command:
AT%XRFTEST=1,1,20,8470,23,1,4,0...
Hello,
I want to program and debug a custom board using my nRF52840 DK (PCA10056 v3.0.3) as the programmer, through the Debug out connector P19. Before I order the cable...
Hi,
We're moving a USB product from an FTDI bridge (FTDI's own VID/PID) to native USB on the
nRF52840, and need to settle its USB identity before release.
Setup...
I was running into issues with issuing the AT#XRESET command for a PPP/CMUX configuration. In an attempt to make the setup as robust as possible we found that the 9151 stopped...
Hi,
We are planning to use nRF Connect SDK Bare Metal (nrf-bm) v2.0.1 but would like to know which toolchain should be used alongside it?
https://nrfconnectdocs.nordicsemi...
We are particularly interested in the following frequency ranges:
2400–2483.5 MHz
2483.5–2522 MHz
2522–2800 MHz
Higher out-of-band frequencies
Could you provide...
My original project contains scheduler mechanism based on nRF5_SDK_17.0.2_d674dde\components\libraries\scheduler\app_scheduler.c. In ncs bare metal v2.0.1, I find the correspond...
So now I have the firmware revision mfw_nrf93m1_1.5.0, updated from 1.4.1 through FOTA. Meanwhile, I tried nRF Connect on nRF93M1 and I have some questions.
1. Most of cellular...
Hello,
I have some trouble to identify my custom nrf52832 board in the VSCODE.
To program the board I am using nrf52840dk, and connect it to my board as follows:
...
Hi,
I have two questions regarding NB-IoT NTN support on the nRF9151 SMA DK:
Does the nRF9151 SMA DK support transmission of 1.25 kHz NPRACH with the currently available...
If a Channel Sounding procedure is aborted while in flight and the ACL is then disconnected, the device settles at a flat ~1 mA with the CPU asleep in the idle thread and...
On a Seeed XIAO nRF54LM20A (application core, nRF Connect SDK v3.4.0, Zephyr GRTC system timer, default LFXO), a minimal application with one 250 ms k_timer and a sleeping...
Device: nRF54L10 (nRF54L15-DK) SDK Version: nRF Connect SDK 3.0.0 Tool: SEGGER J-Flash
Issue Description:
We are using the ZMS (Zephyr Memory Storage) subsystem on the...
Have tried several times to install the SDK into VS code without success. This is one of the errors I am getting:
Failed to register SDK installation: west failed with...
