Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
I want to use the nRF51-DK board as a programmer for my target. As I understand it, this can be done with the signals on P19. However, there is one signal, EXT_RESET, that...
github.com/.../nrf51-UART-examples
Hey any I was trying to test the example, the one with BLE
I test
APP BLE sending --------shows on PC UART software
However, I can...
Hi,
I would like to ask if someone has experience using the AES. I n eed to be absolutely sure that the user SW can use the AES HW block for own custom usage. If yes, Are...
I'm using SDK's interface for AES ECB block, but getting a hard fault when ECBDATAPTR is redirected at ecb_data in the initialisation function:
static uint8_t ecb_data...
I have built the dfu_dual_bank_ble_s110_pca10028 project and attempted to load the ble_app_hrs_s110with_dfu_pca10028 application. I did find that if the use the S130 softdevice...
Hello,
I have a nrf51822 chip using s110 SD. I am trying to read a serie of 14 bytes from UART. If the device is connected to a phone with BLE I receive the correct values...
When my nRF51 DK is only a board without any software.How can I make it work and support for mbed?
If I have to flash the SoftDevice, the bootloader by using nRFgo Studio...
Hi All,
Am developing an app that communicates with an embedded device through Bluetooth low energy.
The embedded device is sending the data in hex format say "35AE51BA44...
Does sample code exist for the pstorage module?
I am calling this code right before advertising_start() in the heart rate monitor application for the newest SDK. It doesn...
Hello,
I used ble_app_uart_c and ble_app_uart exemples on 2 tiny ble boards and S130.
Write and notifications are very slow. Does someone have an idea ?
Connection...
This code do a test triangle with 3 boards on mbed (using BLE API). I have digged in BLE_API and it looks like if instability was in S130. Have you this kind of test in internal...
I've got SLAVE_LATENCY set to 40 in hope that only every 40th request from the master would be responded to since there's no data to read or write, resulting in lowered current...
The question was asked here:
devzone.nordicsemi.com/.../
But not really answered.
Is it really necessary to buy a Dev Kit?
Isn't it possible to obtain a Key without...
