Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
What would be the best way to go about sampling and transmitting a signal at 60 Hz? I am considering setting up notifications and a characteristic, but I don't think that...
Mac OS X 10.10 Yosemite rejects the format of the file system and puts it in a read only mode.
This issue was raised last October 24, 2014 at https://github.com/mbedmicro...
Hey guys,
Sorry to a basic question here, but it's been a few hours and I still can't get a connection to either of two brand new nRF51 dev boards, trying both on WindowsXP...
Hi Sir,
I’m working in an application with the demo board A to communicate via Bluetooth to the demo board B and send data between them. In the module I have to do send a...
I have a 51822-DK board. I have followed all of the instructions to set up the environment. Loaded all NRF tools, Keil v 5, install SDK. I began working on the examples. I...
Hello.
I need to hold 64-bit timer value. I store the 32-bit hardware timer value in one variable (low DWORD) and use an additional uint32_t variable as a an upper part of...
Hi, I'm having a bit of trouble getting the broadcast or HRM example to work. I'm using crossworks and after my last question, removed the retarget.c file and the code compiled...
I am new to smart beacon. We have to make a demonstration of our product i a short time. But I could'nt make it run. There are so many sosftdevice, bootloader and application...
Hi,
Basically, I have a DAC 7562 chip with inputs connected to pin 0.17(SYNC pin), 0.18(SCLK pin), 0.19(TX/Din pin), 0.13(CLR pin), 0.14(LDAC pin) with outputs connected...
I just recently upgraded to SDK 7.2.0 and am now using the keil pack installer as well. First of all, I really appreciate the ease of this new system, but I'm running into...
The new softdevice v8 states that previous revisions(1 and 2) don't support all the new features, and I'm curious how to determine what revision my ic is.
thanks,
akbar
Hi
I have recently purchased an Adafruit Bluefruit LE board ( www.adafruit.com/.../1697) , that uses the nRF8001 chip, so that I would be able to send iOS notifications...
I have a new nRF51822 kit, and although I can (apparently) configure the beacon, it always shows "Beacon not found" when I try to use it.
I'm using an iPhone 5s and the...
Hi, I got new NRF51-DK and dongle with 51422 chip.
It seems that the layout of the memory map has changed with the new SDK and I can't find any information how it should...
