Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi.
I'm struggling with BLE example projects on the my custom board.
my board uses nRF52832-QFAA, 16MHz external crystal with no 32,768kHz optional RTC.
and I choose...
Hi,
I am developing software supporting LEsecure using SDK 12.3 with nRF 51822.
There is a shift to SDK 15.0 as a measure against "nWP - 031", but can not cope with nRF...
i have SDK of mesh version 2.2.0 and nrf5 SDK version 15.1 My question is what are the steps I should follow after flashing the hex file into the dongle. I am using nrf connect...
I am having some difficulty reading the NRF_GPIO->IN. Specifically I have set up one event function for three different input pins, the phase of a motor. The event is on toggle...
Hi Team,
Got a high current issue with uart from customer.
When the nrf_serial_init() is called and the uart is configured as dma mode(used as UARTE), the average current...
Cheers, again!
Our project uses an array of different modules, many of which will need to make use of the TWI manager. I've been able to create the manager successfully...
I'm working on a custom BLE keyboard (starting from the ble_app_hids_keyboard example, S132, seeedstudio nRF52840-mdk board, SDK v15.1.0).
The system is configured to wake...
I am developing on RAYTAC MDBT50Q-DB board.(nrf52840)
I measured current comsumption on RX mode.
with DCDC: about 8mA
without DCDC: about 11mA
datasheet written...
I am working on a LIN slave.
I have working code on an Atmel 2560, just porting it to the NRF52 now. The complication I am foreseeing is that on the Atmel part I could...
i'm using the sdk only for ble serial data transfer, which i'm not using for this pwm test
all code talks directly to the hw registers
those are some code snippets to...
Hi, There are some older comments. Since situation is changing fast and I am un-sure if these comments are out-dated or not.
ROM size. Some comments said 51 is small...
I'm using nRF connect 2.5 on PC and the latest Android app on a Pixel phone. My firmware is based on SDK 15.1 and soft device 6.1.0. I am using nRF52840-DK boards.
My firmware...
Hi,
I would like to know if the nRF51822 chips come with their own valid IEEE address of if we must buy an OUI and generate our own addresses for use in final products...
Hello,
I propose theses evolutions in nrf_bootloader.c, it allows to use gpregret and gpregret2 for other things:
(nrf_power_gpregret2_get() & BOOTLOADER_DFU_SKIP_CRC...
