Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
I am investigating an H4 HCI over a UART implementation for a client which plans to use the 52832 (or 52840) as a replacement for a TI BLE chip in a new design.
I have built...
Hi all
We are using customized board with nRf52810 chipset.
Actual requirement in our project is to send 100 bytes of data for 10 millisecond.
Kindly suggest a procedure...
I'm developing multiple peripheral and a central. Central is only scanning and Peripherals are only advertising.
In the example, I see that I should use the ble_app_blinky...
Hi,
I was trying to run dfu mesh example according to this. I attempted quite few times but every time having an error at step 11.
infocenter.nordicsemi.com/index.jsp...
Hi, Nordic Team
My development environment is PCA10028, SoftDevice 130, SDK12.3.0
I use a s130_nrf51_2.0.1_softdevice.hex.
It is based on ble_app_multilink_central and...
I am new to Nrf52832.......I have started development of a custom board based on Bt832 and BT832X.
I have built 2 proto boards one with BT832F and the other with BT832X...
Starting idle task using Task Manager library frequently throws error "Unknown function at 0x000008C8" when running with the debugger (often takes several restarts until it...
Hi
I'm using sd_app_evt_wait(); to go into low_power mode. For some reason it coming back , but I can't figure out why.
Peace of code I am executing is;
while (nrf_fstorage_is_busy...
I am trying to print out a string debugging information. But got below error.
No problem change to printf or cast char array name to uint32_t. See first 2 sentence.
char...
I have python 2 and 3 on my Macbook. I can't run nrfutil which I believe is due to the python installation. I need to keep python 3 for other utilities. I would like to run...
Hello!
We're building radio modules with the nRF52840, one with the a frontend amplifier and one without. Both are exhibiting excessive 2nd and 3rd harmonic emissions. ...
Currently, we are testing that 「buttonless DFU + Bonding valid」 in our App.
But After performing F / W Update with DFU, other BLE Service became invisible.(※2)
So, as...
Hi,
I am currently in an attempt of revising an old board, it uses an ANT+ module which is soon going to be out of production. With the nRF52840, if I were to use the ANT...
